I hope this isn't a silly question, but I imagine it may be a common one and I wondered how people dealt with it.
We're replacing an old hot water cylinder with a combi boiler, the cylinder was in the airing cupboard and the new boiler is now going downstairs.
We're putting in new radiators...
Hi there, I would really appreciate some help if possible. I have an Ideal Instinct boiler and a Salus RT510TX thermostat. Last night the Salus thermostat stopped connecting with the receiver- there is a red flashing light on the receiver, the heating no longer comes on and it no longer responds...
Quick question guys. I'll make a poll out of the answers and will ask you to vote on it, so that we can clearly find a winner, which we'll then congratulate and stick in some mags and things. :)
I want a quick reply with which suppliers you mostly use. Whether big or small. Online or offline...
Hi all,
Just ripped out a very heavy cast iron bath today from a property I'm doing a bathroom installation on. I heard a rumour that they are worth quite a bit as scrap, is this correct? I'm guessing it weighs in the region of 100kg, definitely heavier than me that's for sure. Was quite...
hi just seen my overflow running from the central heating header tank,when i went in the loft i found hot water entering the tank from the pipe just above the tank ,could anyone please tell me what causes this please ps my radiators are getting hot ok cheers
Hi everyone
Can you tell me if it is possible to connect a new toilet to an existing toilet in the adjacent room by using some sort of connecting pipe through the wall between the two toilets and then have the waste from both toilets to go out into one soil pipe, which is attached to the...
Hello
I recently did a job in a 2 bowl auto flushing urinal system in a small commercial unit. The waste pipe was blocked solid with urine crystal/congealed stuff. I had to cut the pipe to get access and the replaced the waste pipe and S bends. All worked well with the urinals coping with...
Had this come up again last week, and just wanted to pass on this tip:
If you come to a Riello RDB burner which has the motor running but does not attempt to fire, or takes a long time to fire, it can either be the photocell or the motor. Most often it is the photocell. To test, pull the...
Hi all,
I have a problem with my Ideal Icos HE18 Boiler. Went to put my heating on yesterday and nothing is happening. Status on display shows 0. I have a Digistat SCR control with a Digistat RF1 temp control. These controls seem to be working fine as when i turn up the thermostat to heat the...
Hello. I'm a newbie and complete non-diyer. however, I have learned about various parts of my boiler over the past few weeks from bitter experience and the fact it has an intermittent fault that no one seems able to fix! I have an ideal icos boiler displaying an intermittent 'LF' fault code...
Hey guys,
I am new to this forum but from the threads I have read you chaps seem like a helpful bunch.
I have a few customers who want to replace their old showers with a known make (they quoted Aqualisa, Mira and Triton).
I was wondering which make would do you recommend?
Cheers,
Mark
Hi, recently went to look at a customers dripping Damixa tap but could not take any of the tap apart to service it! The only thing you seem to be able to remove is the spout.
I have since found out that the style of taps are the Venus monobloc kitchen range. Apparently Damixa was sold by B&Q...
I need the following in respect to installing a wash basin:
Building Regulations,
Water Beylaws,
Bs6700,
IEE Regulations.
Any help would be appreciated, thanks :)
Hi all!
I have (not for the first time) a problem with my Ideal Icos HE12 boiler!
A month or so ago I had the "FL" error code, which I think means "Flame Failure". I had Gas Safe engineer out and said that the condensate/water for some reason wasn't draining away properly. He rang Ideal...
been to look at a gas pipe job today and the boiler will be 9m away from the meter and there is a fire and a hob .so when calculating the gas pipe the boiler lenght with elbows etc equals a lenght of 15m and there are 3 sections of pipe so the 15m must be multiplied by3 to give a max 1/4...
Hi all,
I've read somewhere that a drop of silicon grease helps for instance when replacing the "o" ring in a mixer tap. Does anyone use the stuff? If so which type?
cheers fellas,
dave
I recently went to a job where the 3 port motorized valve was sticking open. The rads were heating in hot water only mode. I had replaced this valve two years ago. My first thought was sludge in the system. When I tested the water I could not detect any corrosion. The water was yellow, Could...
Recently removed a copper HW tank, the type coated in foam insulation. It is a fairly large DHW tank but I don't know its capacity.
Can you give me an idea of its scrap value please?
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.