Hi all where can I get a aco 202 serviced/ repaired and then callabrated, having a real pain trying to find someone to do this,for such a well know tool thanks
Hi everyone, I think this topic may have been covered before? I'm looking at getting a press gun, more specifically the Novopress, it's just my preference as I've used this and the REMS mini press. I have heard rumors that angled jaws may be on the way for the Novopress but nothing concrete...
Replacing 15 x stopcocks @ 22mm thought I'd try cutters as usually I pull 'em and space was tight.
These Ox brand 22mm cutters just deform the olive and score the pipe.
The jaws don't close properly as witnessed by the burr where the handles meet (pictured) preventing cutting of the olive.
Cost...
Hi.
I've recently purchased a press tool which is branded geberit but it's actually a novopress aco 103.
I was wondering if anyone knew if there was an adaptor that would fit so I can get the machine in tight spaces. I know Rems do a 45° attachment but not sure if this would fit in my...
Armeg jaw droppers. I hears good things and I like a new toy. But both the machine screws on one of them that hold the sliding jaws wouldn't bite and stay in place - no matter how hard I tightened them. Resorted to a fibre washer.
Hopefully things will improve.
Didn't get the nerrad as too many...
Grohe kitchen mixer with new - fangled tool free fixing. Had 2 now, both with problems on the clutched plastic backnut - just keeps slipping and turning, not gripping - tap is about as solid as a fresh mackerel.
They are trying to make it easier for diy / handyman but usually it's the water...
I'm looking for a hole cutter or hole punch that you would use to cut a hole in a stainless steel sink for the waste to install into. Standard hole punches between 40 and 100mm for use with a hydraulic hand tool are available but I need a punch that makes the recess as well or a separate...
Hi, does anybody know what gas is in the freeze master's pipe freezing units, mine could do with a check and a top up. My local aircon branch said they might be able to re-gas the unit if it contained a gas they had. Thanks in advance.
What's with the lack of sds max adapters for diamond cores.
I see countless sds plus bits as well as sds plus to keyed chuck adapter but I can't find any sds max bits.
Any one any ideas
I'm thinking of getting a Stud Finder, so that when I drill or nail something into a wall at home, I don't puncture any pipes, wires etc.
I heard that cheap ones aren't good, not sure if this is true.
Any recommendations would be very welcome 😉
So it is time for me to scrap my vivaro which has just be written off my the insurance company after someone crashed into the van while parked. Lucky as I was just going to dump it this yr any way. Will be sad as have had it for 12yrs.
Any way, need to get a new one which complies with euro 6...
Hi guys looking at upgrading the van and am looking at putting some sort of inverter set up in place. Now I know nothing about these other than I know pure sine is less likely to damage whatever is plugged in. Does anyone have experience of these at all?? Literally JUST looking at it recharging...
Hi everyday peeps,
I need to correct a mistake in the heating system in my dad's flat which has two radiators connected with flow in at bottom and return from the same end at the top. Nothing wrong with TBSE in the right setting, but best not to have the flow and reversed messed up!
Easiest...
Hi
I’ve purchased a basin mixer tap for my bathroom.
trying to install the tap and can’t find a tool to fit the nut that holds the tap in place. I’ve tried one of these and it doesn’t fit. To small.
https://www.NoLinkingToThis/p/basin-wrench/13294
I’ve got a diagram of the tap, need to know...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.