Search the forum,

flexible

Flexible electronics, also known as flex circuits, is a technology for assembling electronic circuits by mounting electronic devices on flexible plastic substrates, such as polyimide, PEEK or transparent conductive polyester film. Additionally, flex circuits can be screen printed silver circuits on polyester. Flexible electronic assemblies may be manufactured using identical components used for rigid printed circuit boards, allowing the board to conform to a desired shape, or to flex during its use.

View More On Wikipedia.org
  1. L

    Cracked private sewer pipe.

    I've recently been doing a bit of work for my Mother, for quite some time now the rear garden has been damp, to the point where nothing will grow as the earth is soaking. It appeared that the private sewer that runs under our patio has cracked so I've dug down and located it, thing is I wasn't...
  2. 1

    Low pressure from moxer tap (hot)

    Hi all I've been round to look at someones new kitchen tap (monobloc) which they have installed themselves. They are concerned as the hot water pressure is very bad, which is mainly due to the fact that the tap is not designed for a low pressure system such as theirs (the cold water tank which...
  3. B

    Sealing gas pipe

    Our college tutor told us when passing a gas pipe through a cavity wall to outside through a sleave you seal the end on the outside so any gas escape can be smelt inside the property,he said if you did it the otherway you wouldnt know if you had a gas leak. I said to him in the BPEC gas book it...
  4. M

    Acrylic Bath Leak

    Hi all, I have a acrylic bath, i have checked all pipework no leaks. When we have a bath we get water coming through ceiling below in the kitchen. I have been told this is common on acrylic baths, is there any tips you can give me. Or would it be better to replace with a steel bath, would...
  5. S

    Which manufacturer

    Hello. I was after some help please, I have searched the forum and can't find anything on the matter. I'm due to start re-plumbing my house next week and need to order the materials. I have decided to go with BPEX barrier pipe (unless someone knows something I don't :]) & push fit...
  6. G

    Leak from waste pipe

    Hello guys, I recently tiled a bathroom and having little knowledge about plumbing I read up on the internet on how to disconnect the toilet so I could lay the ply down and tile the floor rather than trying to cut around the toilet. I've now finished and put the toilet back in but there is now...
  7. P

    Washing Machine Solenoid/Filling Loop

    Hi To All, I know this may sound ridiculous and please forgive me if it is!! All the pipe work to my combi boiler has been hidden behind panelling - including the filling loop!!! I could move the loop and make it more accessible but I was wondering if I used a water inlet valve from a washing...
  8. T

    Connection between L.A.V. and auto switchover

    Hello, I was just wondering if a connection between the auto switch-over valve (including ecv and test nipple) and caravan can be done using two male threaded nozzles connected using lpg hose and jubilee clips? Ideally i would of liked to use 1/2 male threaded hose either end to connect the...
  9. R

    Honeywell bypass valve on suprima

    Hi, I have just been updating a heating system which previously had a gatevalve as a bypass with a honeywell automatic bypass - I cant seem to find any instructions anywhere for the suprima 50 - To set the valve it needs the minimum flow rate for the boiler? Can anyone help? The pump...
  10. G

    Life span of flexible tap connectors

    What is the lifespan of these braided flexible hose connectors that are commonly used to connect to taps? It's just that a standard washing machine hose 10 bar pressure at 25c is recommended to be changed every 5 years or so and these flexible hose connectors are rated only slightly higher at 15...
  11. S

    potterton boiler pressure way too high - HELP!

    I've got a potterton boiler which has been no end of trouble! The pressure gadge is up to 4 and it cuts off probably for safety reasons. I have bled the radiators, and released the water from the flexible pipe attached to the two vavles.# Just checked it again after all that and now the...
  12. A

    Flexible Rainwater Pipe

    I have searched for this via Google and have only been able to find what I required in large coils. So, I am hoping that someone on here can help me out with my requirement. I have a new guttering system in place and I want to transfer the down-pipe flow to a pond nearby. To do this I am looking...
  13. T

    Washing Machine/Dishwasher Waste Pipe

    Hi, I have a washing machine, and the flexible waste pipe is currently fed into a rigid waste pipe which goes out of the building. The rigid pipe is just the right size for the flexible pipe to fit into snugly. I have recently installed a dishwasher right next to the washing machine...
  14. D

    Tiling behind a radiator, weird pipe configuration.

    Hi all, this is my first post and i registered just to get some help with this. I have been tiling and i would like to remove the radiator so i can tile behind it, i have never done this before. I have looked at some self help videos on you tube, but am not confident that my radiator is the...
  15. N

    Connecting electric shower

    I am fitting a Triton Inscriptions electric shower unit, have a 15mm copper straight pipe out of wall & the shower unit has a 15mm plastic straight inlet pipe. I need a 90 degree connector to join them, is there anything special I should use or avoid? :confused: Thanks
  16. S

    Flexible shower hose connected to elbow and fixed shower arm

    Hi, Our bath has a shower handset on flexible hose coming off mixer taps. What we want to do is to have a fixed shower arm and shower head coming from the wall higher up but in between is window and the flexi hose comes out of the bottom of the taps. What we want is to just have a 90 degree...
  17. F

    Copper waste to Plastic

    Heys guys, Need some help. I have to fit a 32mm waste pipe to an "old" 1 1/2 inch copper waste, all internal piping, so cannot remove the copper pipe, so stuck with it unfortunately.:mad: I know there are some fittings out there available, but do you know where I can get...
  18. P

    Classi seal

    My local merchants have all stocked up with this stuff "Classi seal". Classi Seal ® Flexible Waterproof Upstand Seems good and usefull, but im not sure. I've always managed without it but I can see how it would be good. The only guy who i spoke to that used it said it was brilliant stuff...
  19. P

    Heatrae sadia Electromax boiler help

    I have a Heatrae sadia Electromax boiler and when the heating is on it works fine for a while then a demand overheat alarm comes on. The pressure is constantly above 3 bar, when I turn the red release valve the pressure reduces temporarily and then goes back. How do I constantly keep the...
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock