Can anyone help me source some free standing basin taps i know there are free standing taps for a bath but i require them for a basin ie basin height any good suppliers any one can recommend thanks :smile:
Hello chaps,
I've got a job to fit a hand wash basin in a chippy near me. Just wondering if anyone knows the regs, or HSE rules about these?
They want it a few inches from the main sink in a food prep area, there is one in the next room that they use and they have told me they won't ever use...
Hello I have had to replace a 3 hole basin mixer tap valve and can't source a single ceramic valve so have had to order a new complete tap set... Only thing is I've been given a 3/4 size set. When I phoned the supplier they told me it is for bath and basin. I have never fitted a 3/4 basin tap...
Hi,
Clueless amateur here. The rod mechanism controlling the pop-up waste in my bathroom basin has somehow failed so that there is now no rod projecting into the waste pipe to move the 'plug thing' up and down. I've managed to remove the plug so am now left with an unprotected open pipe draining...
I'm changing a basin in my bathroom and have been advised to use a dual flow tap rather than a mixer tap in order to stop any back flow. I haven't had any luck with my local suppliers. Can you advise me .
I have a toilet in the shed.
I was trying to replace the inlet valve but now am thinking of repalcing the entire toielt as it is old and manky.
It is the old type with the cistern up high.
I also want to put in a small wall moutned basin to wash hands in.
====
The problem is that the...
Hi all,
I'm new to the forum and need some advice. I am not a plumber by any stretch of the imagination, but I try my best at DIY.
I have purchased a cloakroom sink from ebay, which was the only reasonably priced one I could find to suite and fit my cloakroom toilet. The issue is all of the...
Leighval
Thread
adapter
basin
find
help
help needed
needed
reducer
slotted
supplied
waste
which
Hi. I am changing the sink taps but have found that the holes are in fact square. Not only that but that they won't budge at all - they're rock solid!! Firstly I need advice on how to remove the taps. I think they originally put putty of some sort and lead. Managed to get the back nut off which...
Calibre500
Thread
basin
holes
install
issue
round
sink
square
tap
taps
At the minute I am using a tap spanner with a big bulky head and the frustration it causes me when I can only turn the tap nut not even a quarter of a turn before it gets stuck between the nut and the back of the sink is over whelming! :32:
Can anyone recommend a 'slim' tap spanner that is...
I have done something stupid.
I was clearing a blockage in my bathroom basin with a plunger. It has an annoying pop up plug that is opened by pushing it down rather than with a lever. I usually put a coin or something in it to hold it open if I am using a plunger, but forgot. To cut a short...
Looking to buy a basin wrench obviously want a one that's gunna last a lifetime, been looking at Rothenberger Telescopic Spring Loaded Basin Wrench, wondered if it was any good much appreciated No.7.0225
I am building a tiled boxed area for a wall hung toilet and recessed basin. When working out where to fit them in the space provided do you half the space and centre this in each half and that becomes the centre of the toilet and basin (llike a vanity unit) or do you make it so the 3 spaces are...
I need to remove a tap from a large ceramic (expensive) basin. The backnut has completely corroded and is not budging. I soaked it in penetrating oil and still no go.
Room around the backnut is limited. There is a rubber washer in between 2 metal plates that go onto the underside of the tap...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.