Hi folks - new here and looking for a bit of advice.
I've got a British Gas 532/i boiler which is struggling for pressure - around 0.5 bar.
Heating works fine through most of the house just struggles to get to the very top rooms.
I don't think any bleeding is necessary, and I cannot find a...
Hi folks - I'm struggling to get pressure back into my heating system after the summer - no bleeding required - but cannot for the life of me seem to find where I'm supposed to fill the thing from.
Pressure is currently at 0.5 bar and I get good heating through most of the house, except the...
Chris James
Thread
central heating system
heating
heating system
repressurise
system
Hi. I am unable to repressurise my boiler after draining to remove some pipes. I have done this several times before it was moved into the loft. The guy who moved boiler is stumped and recons boiler is faulty. It's only 3 years old. Only a small amount of water enters boiler before it stops...
I returned from a weekend away and noticed that the boiler was flashing “0,8 bar”.
I put the heating on and the the “0.8 bar” message has since disappeared but the water level is right on the edge, so it needs topping up.
I’ve looked underneath and below the boiler but I’m still not sure how...
HI I would like to repressurise our Vaillant EcoFit Pure 625. Normally a job even an ignoramus like me can do. However we have no filler pipe and no valves. Could these be inside the case?
System lost pressure, tried to refill using filling loop, no success, turned all trv's off and turned taps off on flow and return to eliminate boiler and still no joy. Can hear water flowing into system and air either entering or expelling through open bleed screw on hallway radiator - the one...
I moved into a house with an already installed boiler. I am trying to re- pressurise it and have followed Worcester instructions, however I have no idea how the boiler has been plumbed.
There seems to be a pump/ filter coming off the main cold water pipe. So when I turn the silver pipe valves to...
Hi I desperately need some help please. We have an oil fed heating and hot water system that has decided to stop working today. Done the obvious checks on the oil, which is fine. But they system is below 1 bar pressure. So suspect this to be the main issue. However I can not seem to be able to...
Ideal Combi bolier. When I repressurise the system to 1bar it almost immediately dumps the water out the condensate pipe before even switching in on at mains. HELP!
I live in Azerbaijan where I have a Wilo MC605-EM pump attached to a Wilo LRS 50/10H diaphragm expansion vessel, which pumps water into my house on demand. We have a large water storage tank sitting between the mains and the pump so there is effectively no water pressure, the pump sucks water...
Hello, I have a Potterton Promax HE Store boiler, and in the past a few times I have had to repressurise the system after getting an E119 error. Usually I take off the bottom cover and turn one valve, hear the water coming in, and watch the pressure increase. However I've got the error today...
Hi all,
I've got my G3 card. First time I've attempted to re-pressurise the white, expansion vessel above an unvented cylinder.
I first turned the water off, ran the taps to relieve the pressure. The vessel (it was flat). I managed to pump it up to 1.2bar with no issues. But then it was...
Hi. I've got an Ideal Heat 15 system and I've noticed a few of my rads need bleeding. I've located the pressure gauge which is above my cylinder and is already reading only 0.5 bar and if I bleed the rads, this pressure is going to drop further.
I've located what appears to be the filling...
Hello, I’m looking for a gas registered plumber in the Newport, South Wales area. I’ve got a leak from the bottom of my boiler when I try to re-pressurise it. Pressure has fallen from 1.1 bar to .7 in 3 weeks. Give me a message if your interested.
Thank you
Hi all,
I cannot find the valve to repressurise the boiler, bled the rads earlier and the CH has cut off.
I've attached the below images, can any body see the correct valve here I've tried a few variations with no success.
Thank you
Hi - I have a Vallian Echotech Pro24 boiler with low pressure and F.22 error displaying. Ive researched how to repressurise and a lot of video/ threads suggest this should be straight forward however there is no flex-loop, no obvious places to attached a flex-loop and no valve taps as described...
Hi, please can someone help. I just moved into a new house and the boiler needs filling up but there is no filling loop. The previous owner did mention how to do this without a loop but I can't recall. I do remember going to the tank upstairs and next to it is a knob which you have to turn after...
Hi guys,
I have been bleeding my radiators due to a small airlock that was present and the boiler pressure has subsequently dropped down. Looking underneath, I am unsure as to how to re-pressurise, doesn't seem to have the fittings as described in the manual. I have the braided filling loop...
I have a SD wall mounted boiler which has a manually controlled refill loop for the heating circuit. It's worked fine until now - the pressure indicator shows 0.5 bar which triggers a fault code and it doesn't seem to want to re-pressurise (done before without problems) even when the refill loop...
Hello, I've just purchased a property that is installed with a Vokera Mynute HE and, due to a small drip, the pressure has dropped. Does anybody know how I can repressurise it? It's currently sitting below 0.5
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.