You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
angled
In Euclidean geometry, an angle is the figure formed by two rays, called the sides of the angle, sharing a common endpoint, called the vertex of the angle.
Angles formed by two rays lie in the plane that contains the rays. Angles are also formed by the intersection of two planes. These are called dihedral angles. Two intersecting curves may also define an angle, which is the angle of the rays lying tangent to the respective curves at their point of intersection.
Angle is also used to designate the measure of an angle or of a rotation. This measure is the ratio of the length of a circular arc to its radius. In the case of a geometric angle, the arc is centered at the vertex and delimited by the sides. In the case of a rotation, the arc is centered at the center of the rotation and delimited by any other point and its image by the rotation.
Danfoss ras-C2 angled thermostic tvr. what way does the arrow face on the flow sde. It's pointing down the way on factory settings. Should it point upwards.
I am currently doing a new build requiring 2 shower trays to use as walk in showers. The tray I currently have does not appear to have angled rims around the edges so water constantly pools at the sealant and doesn't run into the tray and drain. Can anyone recommend d a tray that does have...
Hello, running pipe isn’t a standard part of my day to day as a power generation engineer but occasionally install inch fuel pipe for fuel delivery systems. I am now about to take on a more in dept installation and was after some advice regarding the maths and industry methods of measuring the...
I have 10 radiators with smart TRVs fitted to angled radiator valves - some of these valves are weeping around the plunger shaft - the valves were fitted in 2012 and 8 years seems a short life (I suspect they were cheap!), so I want to replace all 10 valves with better quality valves - but need...
Hi,
My radiator had a leak on stem elbow which is over 20 years old. To stop leak I cut the pipe and put push fit stopper.
i bought 10mm angled radiator valve with 10mm stem elbow. If I put olive thatcomes with valve on stem elbow and tight the valve,the elbow is very loose and comes out of...
Hi,
I have a dripping current valve.
Its after a bit of a saga with plumber. They have told me I will have to get entire new magnaclean that it is connected to. I dont think that is right and surely I can just isolate this valve from other valves in line, and then replace with another angled...
Hi, Has anyone got any experience of these tools? I have a kitchen tap that has a 30mm nut underneath which I cannot get to as it is so tight. I was looking for a 30mm box spanner but came across the above. This would make more sense to buy but some reviews say the gears slip. Cheers Lee
Hi, not sure if this post is in the right place but here it is anyway:
I'm a complete novice when it comes to plumbing so bear with me.
I recently moved house and I am trying to connect the waste pipe from the washer under my sink but apparently I needed a part called a 'long nose...
Hi all,
I've purchased some Valves online and they've come with a brass washer I'm just wondering which side the washers go in. The washer does come apart and one side is larger than the other.
ive attached a picture if that's any help.
thanks Jessie
Jessiethecat
Thread
angled
brilliant
cold
heating
hot
question
thermostat
thermostatic
valve
washer
Hello all,
Would anyone have an recommendations (or advice) please for where I can get a radiator bent at 2 points (to fit into a 3 sided bay window area)?
Many thanks in advance,
Billy
Is there an easy way to fit pan fixings to the floor on a back to wall pan? Other than measuring the distance from the wall to the hole and the distance between the inside of the pan width????
Hi there,
I'm currently redoing my bathroom, new suite and moving pipework under the floor as it was previously on the wall.
Everything was going fine until I started on installing the toilet, it's a new close coupled compact pan and cistern. The problem I have is the old soil stack / waste is...
GeorgeOz
Thread
angled
cast iron
drill
iron
oil
old
soil
soil stack
stack
through
waste
Hi, I'm a new poster but need a bit of help.
any idea how I can raise the temperature of the water here? I presume this is why my heating isn't working very well.
Davidgreer
Thread
angled
attach
heating
problem
screwdriver
temperature
ufh
under floor heating
underfloor
underfloor heating
working
can anyone recommend one for getting into gas valves on the likes of vaillant ecotecs and ideal logics ?? dont know why they have designed them like this but its a pain in the ye know what
OK, I admit defeat. This valve came as part of a TRV + lockshield valve kit, and neither head-scratching nor Google has done me any good ...
The valve comes with a squared plastic knob on it to open and close the valve, and it also comes with a plain cylindrical cap. I assumed that the idea...
Greetings All
Any recommendations on suppliers, manufacturers, ball park prices etc gratefully received.
Also are there any issues with a double panel?
Cheers
Roy
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.