Search the forum,

Van Shaming... Who has the messiest van?

Post new thread

Discuss Van Shaming... Who has the messiest van? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
FILPLASTIC

FILPLASTIC

Messages
25
Well, I've seen lots of lovely photos of (sometimes scarily) tidy vans since we started on here.

The question is, is anyone willing to share photos of their messy vans? I know mine would certainly be in this category if I had a van.

I'll try and sort a couple of free bins for the worst, if we get anyone brave enough to post a pic of course... :smile5:
 
Normally mines a tip, but had to move a fridge freezer for the daughter on Sunday so it's spotless. Well, ish :)
 
I've got a tidy van untill i load it up with all the stuff that doesn't have a space, then i end up just lashing everything in, ive just sorted it out though
 
My old van before I tidied it out!
image.jpg
 
mines not messy,but it could give some bins a home:punk:can i have some bins for being cheeky LOLIMG_20160102_142848453[2].jpg
 
FILPLASTIC said:
Well Chalked, anz & Gas Man, I'll get you some sample bins sorted. Can you msg me your addresses pls to [email protected]. I'm still a bit rusty on the messages section on here!!

I'll leave the thread open in case there are any more messy van pics in future!
Click to expand...
Damit shoulda made a mess in my van too
 
IMG_0511.jpg

a bad day for me :)

if you notice the maroon bag, that was for carrying an ashes urn on the lifeboat for a scattering of ashes at sea. Made a good little towel bag for a while, bit knackered now, also came with the remnants of an arm (very dusty) and when he was dropped over the side, most of him flew back into the wheelhouse with me covered from head to toe, bit of an odd experience going home to rinse off the remains of someone else!!!!!!!!!!!!!!!!!
 
Last edited by a moderator:
The dark side of van p orn.

We've become bored of the unrealistic and unattainable.

Now we experience warts 'n' all. The thrill of the next door look. Reader's Vans.
 
FILPLASTIC said:
The bins have left and should be with you very soon if not already, (Anz yours are going today).

Would love to know what you think when you get them :43:
Click to expand...
Thank you very much for mine.:coolgleamA: especially the drawer unit! I have had the larger version for at least 12 years to keep copper fittings in. It's lost its handle, and has a few battle scars. But still works, so must be a good product. Did you manufacture these then?

Will find a space in the van for the tilt bins.


Once again . Thanks.
image.jpg
 
Chalked said:
Thank you very much for mine.:coolgleamA: especially the drawer unit! I have had the larger version for at least 12 years to keep copper fittings in. It's lost its handle, and has a few battle scars. But still works, so must be a good product. Did you manufacture these then?

Will find a space in the van for the tilt bins.


Once again . Thanks.
View attachment 25023
Click to expand...
my old man had the tiltbin LOL
 
New posts
Status
Not open for further replies.

Reply to Van Shaming... Who has the messiest van? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

S
Advice needed for a mixer Spray for kitchen ?
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
129
Lou
Lou
dreikher
Hole in copper pipe, solder under floor, T coupling & protection
I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
189
dreikher
dreikher
C
Mixer bar fitting solutions?
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
1
Views
201
SimonG
SimonG
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Tiling Advice
Electrical Advice | Electricians Blog
DIY Forum
Electrical News
Tiling Standards BS5389
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock