hot water cylinder, which connector?

[jtsplumbing]

No the tank fitting is not leaking, you could cause more problems trying to remove it, just undo the brass nut , cut out leaking section of pipe, all you need to do upon reassembling is to fit a new 22mm Olive, If you can solder fittings I would remove that faulty section, make up a new section it would be easy to do once removed, then reconnect further back along the side of the wall where it was more accessible.

 

[1animal1]

Oh i see! So upon undoing the nut, the pipe is connected via an olive compression connection? I have only seen one brass version of this nut other than the speedfit and it had a small piece of copper pipe attached (collar) ready to solder a new piece into it. So I presumed I had to go for the speedfit cylinder nut or learn how to solder copper pipe :willy_nilly:....

What your saying is, undo the nut - cut the pipe where it drops down into the floor (lift the whole piece out) leaving enough for a push copper bend to fit onto the piece going into the floor to run level with the cylinder connection, then run a piece from the cylinder with a new olive fitting a new bend to run to the other - and cutting a 22mm piece to connect the two bends...

 

[Chalked]

No the tank fitting is not leaking, you could cause more problems trying to remove it, just undo the brass nut , cut out leaking section of pipe, all you need to do upon reassembling is to fit a new 22mm Olive, If you can solder fittings I would remove that faulty section, make up a new section it would be easy to do once removed, then reconnect further back along the side of the wall where it was more accessible.

Sorry. But that is 100% a cylinder Union. Not a compression fitting.

To the op. If you are going to replace the cylinder for a pressurised unit in a years time. Why not just catch the small amount of water for now.
Or get a friend to recommend a plumber who will sort it very easily. Probably cost £40-£60 depending where you are. You are going to spend £20 on materials to fix. It's not much more for peace of mind.

 

[1animal1]

Easy to say when I have a 4 bed to renovate/make habitable and pay for a wedding next year

I really appreciate the advice, this forum has been invaluable in the short time I've been here.

So the nut doesn't have an olive behind it and the only solution is for the pre discussed speedfit nut and pipe... if I were to attack myself?

The other consideration of leaving it simply won't fit my OCD it's currently leaking a third of a plastic cup a day so presume I'm at higher risk of it bursting if I leave it?

 

[jtsplumbing]

Sorry only took a quick look, but you can still reuse it (Unsolder) or just get a new one and still as B4 replace that section of pipe

 

[1animal1]

Won't i need to solder with a new one as the new ones I've seen come with a collar to slide in a new pipe (to solder).

I don't have soldering gear or experience doing that I'm afraid.

 

[jtsplumbing]

Whatever you desire to do good luck with it, if your lacking confidence to do it, do the prep work and call a plumber to do the pipe work , cant see it costing that much.

 

[1animal1]

Thanks JTS. I've found another online plumbing firm that was able to supply the joint 50% cheaper, and a 1 metre piece of 22mm copper for £4 - should cover this job for £15

Then onto the next one - converting the rads to 10mm from 8mm :toilet:

 

[jtsplumbing]

Any reason why you cant do it in small bore ? micro-bore can cause problems if not done right !

 

[1animal1]

The carpets are staying down for now and until then i'm really not able to get to the main (assumed) 22mm manifold going through the floor. Also because some of it is in the hallway which has new laminate laid by the previous owner. I'll get around to it as i really don't like this small bore stuff - it's a massive PITA when refilling the rads, they take ages! My old 5 (4 very large) sealed system took less than 15 minutes to refill, this 13 rad vented system took me 2 hours not including purging the pump which had air trapped in the cylinder side - school boy error setting that side going first when restarting i imagine :behead:

 

[gassafe]

Sounds like you like to keep re-doing work for the sake of it lol

 

[1animal1]

I just like reliability and the 8mm seems to get really bad reviews, plus it looks horrible! (not mentioning the missus lethal hoovering knocking it) - I have noticed in the short time that i have been in this house how long the rads take to warm up and presume that these smaller pipes have to make it less efficient in the long term? Surely that has to be the case when most of the 8mm fed rads are some of the furthest away in the system...

 

[1animal1]

Purists, close your eyes....

 

[Best]

Well it's taken you four days to do it, but you got there! :smile:
You could have just as easily done it in brass and copper fittings, because if you can get that plastic etc together, you can do it in all metal.
Thanks for getting back and letting us know you are sorted!

 

[Rickster123]

Get some lagging on it quick before anyone sees it!:smartass2:

If it's not leaking and you're happy with it fair play to ya.