Hi all
I have a sticking basin lever tap. I’m trying to take it apart to see if I can sort it, potentially replace the cartridge. I’ve got to the point where I believe I’m meant to remove the copper part of the tap in the picture, however it’s a circular bit that I can’t grip with anything. All...
Been asked to put new childrens basins in a private nursery. This is what I am faced with in the disabled loo.
Apparently installed by qualified electrical firm who are saying the zoning regs dont apply to basins........Someone has installed a shelf above it now to "keep the water out"...
Common...
I have a basin waste and a bath waste that ideally I would like to connect together - to empty into a hopper.
So can I connect a 32mm basin waste to a 40mm bath waste - if so using a reducer or is there some 32mm to 40mm T?
Or should I upgrade the basin waste to 40mm if possible?
Ideally...
Hello
I recently had a new cylinder install. The temperature at the basin sinks is between 56-58C and is far too hot to use.
Is there a legal maximum that is applicable for domestic properties? What should the temperature be for basin sinks? Thanks.
Hi all,
We are replacing our bathroom “hand wash basin on a table” with a basin on a new wall-hung cabinet with a drawer in it. The problem is, the waste pipe outside diameter is 36mm but the space behind the drawer is only 33mm Behind that gap is a 10mm wide strip of wood (about 30mm high)...
Hello, have a 4m run of 50mm pipe for the shower. The layout of joists, closeness of corner walls etc mean that it would be very helpful to be able to add the basin waste to a swept tee in the shower waste and this could be between 300-800mm from the soil stack . I've read elsewhere very mixed...
I replaced the gland on the hot kitchen tap and successfully stopped it constantly dribbling. Problem niw is that the hot tap in the downstairs loo is dripping more. I thought I'd just do the same, but I can't get into it!
Have removed the little cap, and undone an Allen head screw inside, which...
Sorry to ask again about this basin 😂
turns out it’s a **** of a job, done bath no problem but this basin is crazy.
done it with plumbers gold, ptfe tape the lot, still leaking
ended up plumbers golding the overflow and fitting a unslotted, plumbers gold on rim of plug too so nothing gets...
I am looking for a specific basin strainer for one of two sinks in a vanity unit. Cannot find anywhere. Not standard. Will have to change whole waste system both sides if I can't find one. Waste system is designed for the unit so it leaves room for drawers. Depth of strainer about 15mm. D =...
Hi I am trying to figure out my bathroom sink waste problem
Renovating the bathroom and the wife wants the sink the opposite side of the room. The stack is in the opposite corner the only way I can get to it is through 2 joists that have already been cut for the old shower waste.
If I do this my...
Hi everyone,
I hope someone can help thanks.
I have had a new wet room installed and overall it has been done excellent. However, I have one problem and need advice.
As part of the fit it was to get a 450mm wide wall hung basin. It was hung on the wall on top of the new wet wall and gyproc so...
Hello,
I’m trying to fit a diverter to a Grohe concetto single hole mixer tap. I have removed the aerator but cannot find any adapter that will fit as the opening is at an angle. The removed aerator is F22 female and screws onto plastic threads that look like a hexagon when looking up into the...
The basin waste runs horizontally for about 2m in 32mm and the bath waste runs for about 1m before they meet and tee together. From the tee the waste pipe runs horizontally for about 2m in 40mm to the soil stack.
If you look at the pic the top pipe with the level on is 40mm bath waste and the...
The Waste is slightly higher than the trap, I've been advised to use the flexi fitting but it leaks and doesn't look strong enough especially as water remains in the pipe. I would call a plumber, but I know its a simple solution.. for someone! I'm a total newbie so advice would be great!
Also...
Hi everyone, I took pictures to better illustrate my questions and hope it helps.
The hot water pipe under the sink (top pipe) has a valve on it with the number 15 on it and the cold pipe (under top pipe) has a stopcock which stops the water coming into the kitchen sink. Does the cold pipe...
Hello, would be really grateful for some advice, I got a small copper basin in a market in Morocco (way back when travelling was allowed!) I’ve just got round to thinking about installing it and can’t work out what waste pipe fitting to get to connect to it... will post a picture here (if I can...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.