Search the forum,

Discuss Dudley Vantage Pneumatic pushbutton in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
J

Jaded

Hi, I've recently had problems with two of these. One of them was less than a year old. What sort of reputation do Dudley products have in general, and these in particular if possible. T I A, J
 
Bought new item, fitted it, problem exactly the same. So not the push button. Research indicates Thomas Dudley has a good reputation. Suggested source of problem is due to scale build up in valve. J
 
I fit that much Dudley gear I'm well on the way to a Dudley Nike hoody off the profit points :)
 
The unit, (faultless up till now) is a Niagara pneumatic dual flush. 1 of 2 in a retirement flat, roughly 7 yrs old. The failure is due to a fracture of the shoulder holding the pivot end of the flap over the bellows. I've emailed the company to ask if this type of failure is known to them.
 
The unit, (faultless up till now) is a Niagara pneumatic dual flush. 1 of 2 in a retirement flat, roughly 7 yrs old. The failure is due to a fracture of the shoulder holding the pivot end of the flap over the bellows. I've emailed the company to ask if this type of failure is known to them.

7 years of life for a flush valve is a good life IMO
 
7 years of life for a flush valve is a good life IMO

Bring back proper flushing syphons.Nothing to go wrong that you couldnt cure with a bit of coathanger or a circle cut out of a rubble sack!

7 years? A syphon will work for life!
 
Bring back proper flushing syphons.Nothing to go wrong that you couldnt cure with a bit of coathanger or a circle cut out of a rubble sack!

7 years? A syphon will work for life!

no money to be made for manufacturers if their products last too long!


I saw a cast flush valve in a high level cast cistern a few weeks ago, almost 100 years old and still goin strong
 
Be realistic fellers: you can't get high level cast iron cisterns in modern buildings. It's a pity that Thomas Dudley don't have the same high level ( joke ) of good manners. I haven't even had an acknowledgement, from their customer service department. J
 
Status
Not open for further replies.

Reply to Dudley Vantage Pneumatic pushbutton in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two...
Replies
2
Views
184
Every two weeks or so I have to go and top up the system because the hot taps are running cold. Boiler display is flashing 0.6 bar and I fill up...
Replies
2
Views
256
PSxxxxxx
P
Hi, I have an old steel water mains pipe (approx 45mm) that I need to connect to a new pehd water mains (25mm). I can't get at it to create a new...
Replies
2
Views
232
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new...
Replies
1
Views
240
  • Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold...
Replies
2
Views
187
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock