Search the forum,

Discuss No hot water to bath in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Messages
7
Hello all,

We are NOT getting hot water to our bath but red hot to shower and sink.

Is this a easy fix?

if not would it cost a lot?

any advice would be a massive help thank you.
 
here are some pics of boiler and taps.

20190219_201345.jpg


20190219_201334.jpg


20190219_201243.jpg


20190219_201221.jpg
 
Err, 15 & 22mm pipe there on the taps plus PTFE in the wrong places, is there more to this story Brett? Somebody had a play with it?
 
no one has touched the pipes since we have been in the house about 6 years, we got some hot early in the 6years but the last 2 years its gone completely cold.
is this a botch job then?

Wouldn`t say botched just unusal to see different size pipes and yes maybe the joint with the PTFE could be called a botch job. Take it both pipes up to the taps are cold?
 
never thought of that and yes we do get hot water but it seems very temperamental, not had this hot in a very long time

open the tap full and its very cold
I would recommend you call a gas safe engineer to check the boiler over, there are a couple reason for poor hot water performance which should be easy to diagnose.

Also be advised that your boiler will only deliver 10 litres maximum of hot water a min, if you have a good flow rate and open your tap full, the boiler won't keep up with demand.
 
Thank you everyone for the advice it looks like we have hot water now only when we open the tap alittle not all the way. Simple i know but we both dont have a clue about this stuff.

thanks again and we will get the boiler checked thanks

Chances are we don`t have a clue how to do what you two do for a living mate.
 

Reply to No hot water to bath in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
110
  • Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold then would get hot water most of the time. Changing the flow cartridge about 2 years ago (when I moved in) solved this problem enough to suffer it as...
Replies
2
Views
121
Hi everyone, Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Replies
8
Views
262
Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't rip me off? An office guy recommended me to apply for government rebates and get it installed through timetosave.com.au. How reliable is this...
Replies
6
Views
286
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4 times since. It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Replies
9
Views
322
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock