Search the forum,

Discuss Ecodan query in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

stratplus

Plumbers Arms member
Plumber
Gas Engineer
Messages
963
Air source heat pump, unvented cylinder with underfloor heating.
When calling for hot water the flow pipe gets quite hot but when calling for heating thw temp drops considerably.
Is this normal? Why would this be apart from the cylinder will need to be heated quicker?
 
Depending on the outside air temperature, it could be the weather compensation reducing the flow temperature or it could just be designed with a lower flow temp to increase efficiency.
 
Last edited:
It will be built into the unit and still controlled by room stats. Heat pump has an external sensor in the unit. Controller will have heating curve built into software. Most decent heat pumps have weather compensation as standard.
 
Last edited:
It is normal that the flow when heating the DHW should be considerably hotter than when heating the house.

When there's a call for DHW, the HP fault created by high flow temperatures is usually overridden in the ASHP controller so that it can get the DHW up to 50°C plus.

When DHW is satisfied it should revert to heating. If it's an S plan that the heating system 2 port valve would usually be a NO valve so that as soon as DHW satisified the HP can dissipate its heat via the heating circuit (means that in summer even if no call for heat when DHW satisified you'll get a minute or so of flow to the heating circuit), if it's a Y plan, it will do that automatically.
 
Thanks gor that worcester, that explains why all the ones ive installed seemed to ramp up in hw mode.
This particular one was linked to underfloor and a heated towel rail circuit.
Had a 3 port valve to the hw and underfloor manifold and then a 2 port to the towel rail. Individual polypipe programable room stats to each room apart from the towel rail rooms which must have been linked to another stat somewhere. No towel rails fitted so unable to tell although the 2 port was open so calling for heat but no circuit to flow through.
 
Last edited:
Status
Not open for further replies.

Reply to Ecodan query in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hi, Later this year I am going away for a 2 week holiday and as the weather will be warm there is no need for the heating to be on and arguably no need for me to needlessly heat hot water. My intention was to turn the boiler off along with the mains water when going away. Now, I have heard...
Replies
1
Views
126
  • Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold then would get hot water most of the time. Changing the flow cartridge about 2 years ago (when I moved in) solved this problem enough to suffer it as...
Replies
2
Views
161
Hi, I have a Worcester 28i junior boiler that has started to lose pressure, only when using the central heating. When using hot water I have no issue, however, when running the heating the pressure drops. Im looking for some ideas on what could be causing this. I have no sign of pipe leaks...
Replies
6
Views
213
Hi everyone, Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Replies
8
Views
328
Hi, I'm looking for a water pump to pump water from a storage tank at a constant 3 bar pressure. It's at a campsite I run that's at the bottom of a long, steep hill. We struggle with very high and often fluctuating (around 7 bar) water pressure, which wreaks havoc with our water heaters. I've...
Replies
2
Views
63
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock