Search the forum,

Discuss CADENT (NATIONAL GRID) in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

Harvest Fields

Esteemed
Plumber
Gas Engineer
Subscribed
Messages
10,444
Just had to call CADENT our to cut a gas main off for having a 23.5mb standing and 6.0mb working pressure. Yes, I did say 6.0mb. Never had one that low before.:eek::eek::eek:
 
Nope I've had 14 that's the lowest
 
I had 4mb once. Could only just get a flame on boiler, went out when cooker turned on.

Don't know why you asked grid to disconnect.

Phoned it in and they they came out and fixed it within two hours as usual.
 
He couldn’t get it any better and it needs a new main. He couldn’t get anyone out until tomorrow.
 
Grid would not cut off a supply 'cos an RGI asked them to. The RGI presents the problem, and they decide upon the appropriate (in there view) course of action
True dat mate. True dat. I was hoping they would fix it there and then. But then again wasn’t he the one that said he would do a boiler change for £1000.00?
 
tbh nation grid Sod me off. By me they now wont touch a main that has 17mb or higher at ecv nut. They wont test with the boiler in service mode so moduation gives them another excuse. they have lowered gas mains pressures to around 25mb because the mains leak so bad. they will try anything to avoid costs.

the other problem is they are paying private contractors to plastic line the mains, these guys are on price work and tend to do a really bad job. sometimes they use 16mm pipe inside the old main and if its found out after 2 years the private companys warranty is passed so the grid has to pay to replace. total codge job.
 
There is loads of main grid replacement going on around my way at the moment. Putting smaller pipework inside the old has resulted in many properties having a low service pressure. When I have called them (many times this year) they have come out replaced the main properly and then buggered off.
 
Status
Not open for further replies.

Reply to CADENT (NATIONAL GRID) in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
136
Hi all I'm hoping someone can shine a light on this for me Since our stop tap on the pavement has now been filled with sand for whatever reason, we are relying on our property fitted stopcock (this is outside on our garage wall) Unfortunately turning this to the closed position only reduces...
Replies
3
Views
252
I have had a look at previous posts and think I know the answer to this but just before I make it worse could I just check what you think about this one. Granddaughter just moved house and this valve decided to leak when it was closed. When open its fine. Normally I have repacked the gland on...
Replies
7
Views
191
We run a community village hall and have a large kitchen provided for the use of hirers. This includes a Lincat SLR9 gas cooker which I believe is a 23.8Kw appliance with all six burners and oven on max. This was installed some 10 years ago and has passed all subsequent Gas Safety inspections as...
Replies
5
Views
473
I have a green star ten yrs old keeps increasing pressure, feel on off filling valve not working, drain off to recommended, but after few days it's increased whilst cold...is this a regular problem.
Replies
1
Views
146
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock