4 inch elbow

[jaydebruyne]

Is this likely to be a solvent weld elbow?? Sorry for the bad picture..

I have to replace the pan connector but not seen this kind of elbow before so just sussing what I need.

 

[townfanjon]

No pic jay

 

[jaydebruyne]

Oops...

 

[ShaunCorbs]

yea looks like sw bet there is no 4" pipe on the collar thats why its leaking

 

[plumben]

I'd vote for solvent weld as well,

 

[jaydebruyne]

Are there no elbow pan connectors but with a long stem from the pan going to an elbow with a short male connector for the 4 inch stack...??? They all seem to be the other way...

 

[ShaunCorbs]

Are there no elbow pan connectors but with a long stem from the pan going to an elbow with a short male connector for the 4 inch stack...??? They all seem to be the other way...

extended bent pan connector and how long to looking for?

 

[stevetheplumber]

there are two sizes of pan cons

 

[stevetheplumber]

sorry imeant to say there are two sizes of bent pan con try the macalpine book to get dimensions the pciture looks like a pan con into an old terain pan connector which will work if you put a bit of 4 inch onto the second one

 

[jaydebruyne]

extended bent pan connector and how long to looking for?

I can only find these.. I need it the other way around..

Basically as long as the elbow plus a few inches

 

[anz]

McAlpine 90Deg Bent WC Connector With Extended Inlet WC CON8E

 

[ShaunCorbs]

I can only find these.. I need it the other way around..

Basically as long as the elbow plus a few inches

section 5 1 (stnd) and 3 (extend) any help?

http://www.mcalpineplumbing.com/media/cat/35.pdf

 

[jaydebruyne]

I'm think I'm just gonna hack off the sw elbow at the base and stick in a flexi as I don't think the extended inlet pan connector is quite long enough... it only gives me 80mm for the inlet

 

[ShaunCorbs]

I'm think I'm just gonna hack off the sw elbow at the base and stick in a flexi as I don't think the extended inlet pan connector is quite long enough... it only gives me 80mm for the inlet

can you leave the elbow in ? (split?)

 

[jaydebruyne]

can you leave the elbow in ? (split?)

There isn't much room between the elbow and the pan, def not enough to weld some 4inch pipe in place

 

[ShaunCorbs]

There isn't much room between the elbow and the pan, def not enough to weld some 4inch pipe in place

straight pan connector? or are you changing the bog

 

[jaydebruyne]

straight pan connector? or are you changing the bog

No the pan is staying.. Yeah I'm gonna try a straight first, if that fails I'll go with plan b

 

[ShaunCorbs]

No the pan is staying.. Yeah I'm gonna try a straight first, if that fails I'll go with plan b

just glue enough 4" in to fit flush with the elbow if there non there

 

[jaydebruyne]

just glue enough 4" in to fit flush with the elbow if there non there

Cheers Shaun

 

[ShaunCorbs]

Cheers Shaun

np you understand what i written ?

 

[jaydebruyne]

np you understand what i written ?

Yeah course... Why you ask?

 

[ShaunCorbs]

Yeah course... Why you ask?

just asking its getting late and sometimes my words get mixed up

 

[jaydebruyne]

just asking its getting late and sometimes my words get mixed up

Same happens to me after a bottle of wine

 

[chris watkins]

Is this likely to be a solvent weld elbow?? Sorry for the bad picture..

I have to replace the pan connector but not seen this kind of elbow before so just sussing what I need.

If I am not mistaken it is a Terrain 102.4.5 Bent (or 125.4.5 straight) See Page 13. It is a single rubber seal pan con & someone has just stuffed another straight con directly into it which is not allowing the fins to seal. Suggest removing the black rubber seal, it just pulls off, buy an extension multikwik, push down inside so it seals in the inner pipe. Then cut to length & re-fit the standard pan con you have already fitted. (Say No to Flexi's) http://www.plumbcenter.co.uk/wcssto...ng.all/hu/re/Polypipe_TerrainS&W_Brochure.pdf

 

[jaydebruyne]

So the socket of the elbow is 5 1/4 inch... The black rubber seal has gone. Merchant suggested putting a fernco reducer over the elbow socket, some 4 inch in the other end and the straight pan connector.. isn't there anything that'll go into the elbow socket?

 

[ShaunCorbs]

So the socket of the elbow is 5 1/4 inch... The black rubber seal has gone. Merchant suggested putting a fernco reducer over the elbow socket, some 4 inch in the other end and the straight pan connector.. isn't there anything that'll go into the elbow socket?

dia?

 

[jaydebruyne]

dia?

Yup

 

[ShaunCorbs]

Yup

you 1000% sure (taken the bog out and checked? and is it a block of flats?

 

[jaydebruyne]

you 1000% sure (taken the bog out and checked? and is it a block of flats?

Took toilet out to remove pan connector as no give.. measure it then. Yup, block of flats. Discharge pipe is 4 inch

 

[ShaunCorbs]

Took toilet out to remove pan connector as no give.. measure it then. Yup, block of flats. Discharge pipe is 4 inch

central stack and sorry to say if the elbow is 5.25 your only option is a fernco reducer sorry to say