Search the forum,

Discuss parkinson Cowan Windsor radiant gas fire in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

stani

Esteemed
Plumber
Gas Engineer
Subscribed
Messages
2,505
does anybody have a pdf copy of the above fire MI's
I think it is somewhere around the 1970's
brief description of the appliance=====3 radiants, copper canopy, horrible curved legs. no fsd , awful looking thing.

any help much appreciated.
 
Hello. I desperately need this very same manual so this charming old fire can be installed in my new home.
 
does anybody have a pdf copy of the above fire MI's
I think it is somewhere around the 1970's
brief description of the appliance=====3 radiants, copper canopy, horrible curved legs. no fsd , awful looking thing.

any help much appreciated.

Is this manual available? I desperately need it.
 
That fire must be around 37 years old now.

Where did you get it from?
 
My first one was installed in my home 42 years ago. Since it malfunctioned, I bought one on eBay. My installer says he must have the installation manual to do the work. That's why I am looking for it.
 
That fire must be around 37 years old now.

Where did you get it from?
My first one was installed in my home 42 years ago. Since it malfunctioned, I bought one oneBay. My installer says he must have the installation manual to do the work. That's why I am looking for it.
 
Don't think I would fit a fire that old. Especially from EBay. But everyone to there own.:eek::(
 
Don't think I would fit a fire that old. Especially from EBay. But everyone to there own.:eek::(
Do you still need a copy of these? Only have them for a short time but I can copy them?

IMG_9727.JPG
 
How tech savvy are you harvest ?
 
Np as it's not in a private bit will pm you
 
Status
Not open for further replies.

Reply to parkinson Cowan Windsor radiant gas fire in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

We run a community village hall and have a large kitchen provided for the use of hirers. This includes a Lincat SLR9 gas cooker which I believe is a 23.8Kw appliance with all six burners and oven on max. This was installed some 10 years ago and has passed all subsequent Gas Safety inspections as...
Replies
5
Views
502
Hi everyone, Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Replies
8
Views
326
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
168
We are from Alberta, and I own an electrical company. I have been asked by a BC Mechanical P. Eng. to install an emergency STOP button at the man-door to the boiler room. It's intent is to 'halt' the operation of the boilers in the room should there be an emergency. He is demanding that I do...
Replies
5
Views
291
I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
215
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock