Search the forum,

Gloworm ultrapower 170 sxi

Post new thread

Discuss Gloworm ultrapower 170 sxi in the Plumbing Jobs | The Job-board area at PlumbersForums.net

A

Abbie Phillips

Messages
3
Hi
My boiler is not working after a heating engineer looked at it yesterday. Getting t9 code despite resetting and re-pressurising. The filling loop hose is now leaking. Can anyone tell me how I switch to the immersion so I can get hot water until engineer comes back out. Many thanks
 
There is usually a fairly obvious switch positioned near to the hot water cylinder. Pictures of the cylinder and it's surround would help if you're still not sure.
 
Hi. Thanks for your reply. Don’t know whether these photos will help, the tanks incorporated in the boiler system. Thanks

FD7CCDF6-109C-4290-9F71-836DC23221F3.jpeg


8358A32C-44BB-4674-86E0-178C3AE7E719.jpeg


57423466-86B5-4D6E-A2D0-93919FD196F1.jpeg


76DC5981-1238-4FAC-8853-6E1936658E23.jpeg
 
Abbie Phillips said:
The filling loop hose is now leaking.
Click to expand...

Your photo appears to show the valves at either end of the filling loop open and partially open. Once you've got the system correctly pressurised both should be set to the 'off' position, this is normally with the lever at right-angles to the valve body. This will stop the hose leaking.

(Strictly speaking, once the system is correctly pressurised the flexible loop should be disconnected and the valve ends sealed with screw-on caps.)
 
filling loop is open in the pics?
 

Reply to Gloworm ultrapower 170 sxi in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

M
Central heating losing pressure all the time
Every two weeks or so I have to go and top up the system because the hot taps are running cold. Boiler display is flashing 0.6 bar and I fill up to 1.3. I've had an engineer look inside the boiler and he can't see anything wrong. I've checked the pipes all over the house and cannot see any...
Replies
1
Views
120
fowlerboi
F
P
Viessmann combi starts when cold, mixer, tap is opened
Recently had a Viessmann Vitodens combi boiler installed, quite often when the adjacent cold mixer tap is opened the boiler starts for a few seconds! Can anyone tell me what is causing this? And how to cure?
Replies
3
Views
196
ShaunCorbs
ShaunCorbs
S
Advice needed for a mixer Spray for kitchen ?
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
107
Lou
Lou
jamespipe
Plumber recommendation for heat pump HWS installation
Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't rip me off? An office guy recommended me to apply for government rebates and get it installed through timetosave.com.au. How reliable is this...
Replies
6
Views
285
oz-plumber
O
F
  • Question
No Hot water, Fixed and Broken Again Ideal Logic 24
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold then would get hot water most of the time. Changing the flow cartridge about 2 years ago (when I moved in) solved this problem enough to suffer it as...
Replies
2
Views
117
Lou
Lou
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock