Where to buy boss (double Socket – same side)

[Klorr]

Where can I get hold of a boss (double Socket –same side) 110mm x 40mm
I've goggled this and can't one.

Like this (I photo shopped this picture)
https://1drv.ms/i/s!AlXOOGaTv36QgQuVPv22GNk2dCzK

 

[ShaunCorbs]

Just glue two strap on bosses onto a piece of pipe done

 

[Poppa Spike]

yep, two strap on bosses the way to go.

 

[Klorr]

I know you can use straps but can you not buy doubles on the same side ?

 

[rpm]

Warning- It`s for underground connections and Kloor will go for her guns if you call her mate!

:49:

lol

 

[joni os]

Bossed connection not normally used underground. Would normally Tee off 110x110 and reduce to 40mm above ground. Please give further details of installation.

 

[rpm]

http://www.ukplumbersforums.co.uk/bathrooms-showers-wetrooms/93018-how-do-i-plumb-shower-waste.html

 

[Chalked]

Why don't you just use two polypipe short boss pipes?
View attachment 27700

 

[joni os]

http://www.ukplumbersforums.co.uk/bathrooms-showers-wetrooms/93018-how-do-i-plumb-shower-waste.html

In the above situation connecting to external 110mm underground, the standard method would be to connect via a back inlet gully. These now come with removable internal sleeve, allowing direct rodding to main run. I know the length of run may be minimal but building inspectors can prove rigid on such matters,

 

[Best]

Why can you not use two of the 110 x 40mm bosses joined together? They will meet up tight, similar to what you showed

 

[rpm]

Maybe Kloor`s alternative is the way to go?

https://1drv.ms/i/s!AlXOOGaTv36QgQjSNZa1BdvGWKrI

 

[Klorr]

Yep - that shows you what I have in mind for the double connector

PS my dad calls me "mate" all the time
PPS the reason for not using 2 bosses is that I just trying to be tight - mind you may cost more to get a double

 

[joni os]

Connections into vent not underground, post 5 misleading. Sink waste can boss onto vent up to 500mm above ground. Shower waste depends on branch to WC. 110mm Tee to WC with provision for 40mm boss at 90 degrees would suit if branch can be positioned low enough to give 1:40 fall from shower but best solution would be to have WC branch coming in at level of WC outlet, approx. 150mm above floor and use new back inlet gully, connected independently to main run, for shower and sink waste. Tell your plumber to start digging.

 

[Ray Stafford]

A polypipe SWA43 gives you two boss inlets in the same plane on the same fitting.

Costs way more than a pair of strap bosses though...

 

[tamz]

Or alternatively use a soil manifold which may work out better

 

[tolly]

Am I the only one that dislikes strap ons...oo err.

much rather have a boss pipe where possible, strap ons a last resort for me

 

[Best]

Am I the only one that dislikes strap ons...oo err.

much rather have a boss pipe where possible, strap ons a last resort for me

I also never liked them. Handy if a boss fitting is a hard job to fit. They always look an add on and if the solvent has been plastered all over the joint makes them an eyesore.

 

[snowhead]

Double socket, same side
And it looks like 2 the other side as well.

Turn the 110 branch into a rodding access.
Or turn it around and bury it in the wall.

110mm PVCu Solvent Weld Soil Pipe Bossed Branch 92.5 Degrees Double Socket 453