My Superfire 2 is now leaking gas from the pressure relief hole ( just below the trigger).
It is 14 months old and looks like new. The previous one did exactly the same but i think I got about 3 years out of it.
I spoke to Rothenberger . They tell me they wont warranty their torches if you...
Hi.
I've recently purchased a press tool which is branded geberit but it's actually a novopress aco 103.
I was wondering if anyone knew if there was an adaptor that would fit so I can get the machine in tight spaces. I know Rems do a 45° attachment but not sure if this would fit in my...
Hi I am trying to replace my bathroom tap with a new one, I am trying to remove the existing rusty flexible tap connectors from this bit of 22mm copper pipe.
But this thing is not budging at all its like its welded or super glued on, I am using some water pliers on both points here but its not...
The drain cock on my water cylinder is very close to the ground and is obscured by piping installed by the previous owner. The spigot is at the bottom but, try as I might, I can find nothing to tighten it. Can anyone offer any advice ? Thanks
Which make is fairly foolproof? I tend to almost always go down the mechanical unblocking route but I want to leave a few bottles for a few tenants (not mine).
Evening all,
As per the title does anyone know where I can source an extension bar for hole saws?
Scenario today: using 54mm hole saw through approx 300 mm wall made up with plasterboard with a ply backing, cavity, a layer of osb, insulation and then a brick outside wall
(Obviously aware you...
I've found this website called gasqet.com. They make 3D printed washers made out of a different plastic that is higher spec apparently, so it's a lot stronger, and recyclable (though why you'd want to, I have no idea). But they are the same price as normal washers.
Has anyone tried them out...
Just a heads up pretty cheap for 250ml
https://www.ebay.co.uk/itm/Loctite-577-50ml-250ml-Fast-Cure-Medium-Strength-Pipe-Seal-fast-shipping/352877949177?pageci=66774372-c39b-40e9-9b61-2f00496a6e85
I'm looking for a quality robust sealant between rubber bathroom flooring and sanitary ware as well as gap filling between floor and skirting, it's not a wet room but needs to go off hardish and be easy to clean. Does CT1 fit the bill?
We are looking for a toilet with a good design and a powerful flush as one of our family members produces rather large stools that get jammed in our current toilet - which was an emergency purchase from wicks and was very cheap, we are now ready to spend a little more for something that can do...
I need to replace 13 TRVs due to sticking issues, I saw that Honeywell do a tool to remove and exchange the TRV inserts', this will save me draining the system and saving time, anyone know where I could hire one from?
Cheers
I am trying to undo the non return valves on my shower to clean them but they won't budge, I guess there is a tool for doing this but can't find one on line - help would be appreciated!
It's basically a very wide slot but my largest screwdriver does not do the trick, the maintenance...
Anyone used the nylon guides eg
https://www.benditnow.co.uk/product/b1522pg-plastic-guide-set-15-22mm/
Say there more durable than the alu ones any thoughts ?
Hi guys
I have been asked to install a new electric shower at a property. The customer is saying her old one has no power. She has a combi boiler so can’t fit a power shower and the original shower only has a cold water feed.
I am looking at investing in a rothenburg flow cup.
Are they any good...
I’m moving from USA to the UK and with my tools is my Milwaukee ProPress gun. I am under the assumption that I will need to leave the 1/2” 3/4” and 1” jaws in USA and buy new 15, 22, 28 jaws in the UK unless someone here might know if the imperial jaws will press metric fittings too?
Thanks in...
Replacing 15 x stopcocks @ 22mm thought I'd try cutters as usually I pull 'em and space was tight.
These Ox brand 22mm cutters just deform the olive and score the pipe.
The jaws don't close properly as witnessed by the burr where the handles meet (pictured) preventing cutting of the olive.
Cost...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.