I've had a spate of low pressure issues recently.
MWP @ about 17.5mb
Centrica engineers are a special breed but I couldn't take being told again that I was wrong so I asked the last one to prove the pressure was OK. The guy quite confidently passed me his basic u-gauge to confirm my digital one...
The flue for a glow worm micron 30ff is apparently obsolete but there must be other flues that would fit it surely, it's just a standard 100mm horizontal flue right?
I mean when a bg gas engineer tells you that you'll have to change the whole boiler as well because you can apparently no longer...
I saw on a plumerparts posts comments that the gas engineer always used an inline filter on the gas line to the boiler due to debris.
I’ve just had a new boiler fitted, is it a good idea to ask my installer back and pay for a filter to be installed or a waste of money as the gas isn’t that...
Hi guys
I'm moving to a flat but where the cooker is situated. I can't get a vented extractor fan as it's the same wall as the next door flat.
Are the none vented ones any good ?
Which one should I be looking out for ? Or avoid ?
Any tips will be helpful
I run a small plumbing and heating company. I am looking for a commercial gas engineer to help out with a few call outs, servicing, safety checks etc. Most work around London, Kent, Surrey, Sussex area.
Ideally looking for someone self employed or another small business who could work...
Hi everyone I currently work in oil and gas industry working in North Sea and further afield operating on high pressure oil and gas plants. This line of work means I have on average 6+ months off a year, im thinking of training to become a domestic gas engineer in my time off to earn a bit extra...
Hi guys,
any meter installers about?
im looking to complete a course to get CCN1 qualified and met1 qualified so I can look at becoming a smart meter installer.
once qualified all employers seem to want 6 -12 months experience as a meter fitter. How do you guys gain the first years...
Hi all,
I have recently returned to the industry and have applied to Octopus for the upskill role into air-source heat space installs. Does anyone work for them on here? Just wondered what people's thoughts were on them as a company and if anyone is fitting air source what they think of this...
My first post here, looking for some advice.
I've just had my boiler replaced with a worcester 4000 combi boiler. The engineer put chemical flush and inhibitor in when filling up, ran the raditors hot and then tested using a strip. And has left both in saying this is safe, and standard...
Has anyone managed to clean the tubes inside the manometer? I have dirt inside mine which has been building up for ages, it could even be mould in it. I'm not sure how to clean it, due to the thin tubes.
Any ideas?
Cheers
My installation has been classed as Dangerous 'Do not use' by my boiler manufacturer. I have an Ideal Logic 30kw Combi boiler mounted as high as can be on the kitchen wall. Flue exits out through the wall via an elbow but emerges above a flat roof. Unfortunately it's somewhat less than the...
Can anyone turn a boiler off to work around the flue for roofing as an example, as long as a registered gas engineer carries out the required checks and certification before turning it back on?
Hi
Fitted a new out the box’s boiler today. It worked for 30 minutes. Then stoped and went to fault codes
2965
B Flow temperature too high
▶ System is not filled with water.
▶ No water flow,because CH system is closed.
▶No water flow, because pump is not operating correctly.
▶ Check flow...
Hi, my mother had an electric cooker installed yesterday. The guy who fitted it said it shouldn't be close to the gas pipe but it is.
The red arrow shows the gas pipes, the blue arrows are the electric supply for the cooker and the purple is the back of the cooker.
I know nothing of plumbing...
Hi all. Got to run a Vailliant flue externally and been told by vailliant I need a heat resistant flexible silicone. Can anyone recommend which silicone to go for? Cheers
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.