Discuss vailaint f75 no hot water no heating? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

Super Mario

Gas Engineer
Messages
160
hey guys i have a vailaint eco tech plus with f75 pressure relief is not leaking i cant find any leaks on system( wooden floors) Do you think its the pressure vessel that needs changing? cheers
 
Isn't this a known issue with them? thought there was some kit you got free of charge?
 
It's in public so it's a no no! The issue is with the appliance and you need to be GSR to do anything inside this as the case is combustion seal!
 
Last edited by a moderator:
Isn't f75 cheese in the flux capacitor? Or is that 6f5 ?

No 6f5 is recycled capping

e4a2u8am.jpg


Defo capacitor or the reality matrix
 
Last edited by a moderator:
Flow switch left side of boiler. Depending on which model you have it is a bit awkward to release the circlip. Also check your pump.
Good luck.
 
Doh outside comments gone now ;)
 
Last edited by a moderator:
Moves to private forum.

Pressure transducer not detecting a 0.2bar rise in pressure when the pump kicks in. Check water quality, pump, transducer.

Then get an f75 kit.....

Watch where you're posting in future.

You too Manx.
 
Last edited by a moderator:
You can verify this by bumping pressure. Just over fill and prv bouncing it ritz off will shake air bubble out of sensor, it will reoccur within hours. New sensor mod required
 
Last edited by a moderator:
if pump is pulsing on/off check water pressure sensor, on x2 on p.c.b 5vdc from back wire to red, black to green will depend on what pressure is in system ie 1vdc= 0bar, 1.6vdc=1bar and 3vdc=3bar. if voltage is incorrect on green to black more likely just need replace water pressure sensor.
if you got existing rubber hoses on flow and return then its worth ordering f75 kit
as in time they will split. you get copper pipes with new water pressure sensor in f75 kit
if already copper pipes then cheaper order sensor.

if pump isnt pulsing on and off then check pump
 
Last edited by a moderator:
The last company I worked for were paying about ÂŁ170 for them and the company were doing 3/4 a week
 
The small plastic bit to lift up flow sensor? Or the full rubber hoses kit?
 
You can buy just the sensor mod in sure! As I said less than ÂŁ20
 
Status
Not open for further replies.

Reply to vailaint f75 no hot water no heating? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

I have been facing central heating low pressure on unvented hot water RM Cylinders but can't see any leak on the PRV, expansion vessels and...
Replies
2
Views
510
losing pressure
L
Looking for any ideas to help. I've a Heatrae Sadia Hot Water tank, heated through Oil fired boiler (working fine). A week ago I reset the air...
Replies
8
Views
350
  • Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold...
Replies
2
Views
237
The Water Board have just replaced the main water supply to our property. We have a ground floor combi boiler. The central heating system for the...
Replies
9
Views
573
I have a Vaillant eco plus 837, year installed 2008. It works well. We have one large zone for the house with 13 rads running off it. We also...
Replies
1
Views
340
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock