Search the forum,

Discuss Radiators not hot enough in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
Messages
1
I have recently moved into a new home and replaced some of the radiators. A couple of them are larger double panels compared to what they originally were. In total, 3 large type 21's, 2 large type 22's and 2 small ones.
It is a regular vented system with a cylinder and tank in loft.

Now it seems the radiators do not get hot enough. They are hot, but compared to where I used to live, the radiators used to get too hot to touch, where as I can touch the new ones comfortably. As a result the rooms takes forever to warm up, and never really reaches the desired temp of 20-21c.

So the most obvious cause to my untrained mind would be the boiler doesn't pack enough power to deal with the new rads. It is an old boiler, possibly 15-20 years old.

But could it be something that could be a quick fix in the short term?
I have bled all the rads, and do so regularly.
I have turned the pump up from 2 to 3. This has helped slightly, but not enough.

Given the cost of moving home etc, I don't really want to replace the boiler right away, so if anyone has any alternative suggestions on how to improve the situation, I would be grateful.

Thanks
 
I have recently moved into a new home and replaced some of the radiators. A couple of them are larger double panels compared to what they originally were. In total, 3 large type 21's, 2 large type 22's and 2 small ones.
It is a regular vented system with a cylinder and tank in loft.

Now it seems the radiators do not get hot enough. They are hot, but compared to where I used to live, the radiators used to get too hot to touch, where as I can touch the new ones comfortably. As a result the rooms takes forever to warm up, and never really reaches the desired temp of 20-21c.

So the most obvious cause to my untrained mind would be the boiler doesn't pack enough power to deal with the new rads. It is an old boiler, possibly 15-20 years old.

But could it be something that could be a quick fix in the short term?
I have bled all the rads, and do so regularly.
I have turned the pump up from 2 to 3. This has helped slightly, but not enough.

Given the cost of moving home etc, I don't really want to replace the boiler right away, so if anyone has any alternative suggestions on how to improve the situation, I would be grateful.

Thanks

Hello Miki,

Please don`t be offended by this question:

Have You made sure that the Boiler Thermostat is turned up to the Maximum setting ?

I am sure that You have but `just to make sure`.

I have had people ask me about their Home`s Central Heating not working correctly only to find that the Boiler Thermostat was set to a low temperature which meant that the Radiators were not getting hot enough to heat the Rooms / Home.

IF the Boiler Thermostat is NOT set at the Maximum when You look at it [you might already know] then you will probably have a very easy `Fix` by just turning it up - unless there was a reason why it was turned down.

Regards,

Chris
 
Assuming it's not the Stat as above.

To prove whether the boiler is undersized try turning off some of the other radiators in the house, effectively diverting all the boiler output to the new ones.

If that doesn't improve the temperature then the pipework to the radiators may be undersized.

How well does the output of the radiators compare to the heatloss calc for the rooms?
 
Status
Not open for further replies.

Reply to Radiators not hot enough in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

I want to reconnect some outbuildings to an existing water supply. The supply pipe is old 22mm MDPE and buried for a fair distance so not going to dig it up and replace it 😬. Question is can I use normal 22mm plumbing push-fit connectors to make the connection as finding 22mm MDPE fittings...
Replies
1
Views
274
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4 times since. It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Replies
9
Views
350
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
1
Views
207
Hi, basic question, any insight much appreciated. Looking to have an outdoor tap in my front porch fed from 15mm pex coming up from suspended floor. Pic 1 is inside porch, pex temporarily clipped to give an idea of pipe placement (ignore shoddy blockwork of booted cowboy builder!), Pic 2 is...
Replies
6
Views
242
Hi all I'm hoping someone can shine a light on this for me Since our stop tap on the pavement has now been filled with sand for whatever reason, we are relying on our property fitted stopcock (this is outside on our garage wall) Unfortunately turning this to the closed position only reduces...
Replies
3
Views
272
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock