Potterton Promax HE 15 2004

[Lee Davies]

er
OK, so here is an update on this boiler to see if anyone else is the wiser.

I actually got longer than 15 minutes in the property today.

I cleaned out the condensation trap, this was blocked, therefore causing the boiler to lockout. The trap was full of 14 years worth of aluminium by the looks of it from the HE.

Checked the case seals on the CC and they are not passing, therefor I didn't remove the combustion chamber door and it isn't the overheat stat on the fan causing lockout.

Fan is working correctly, 3 port valve is working correctly, pump is working correctly, electrodes are sparking correctly (I removed them to check spark strength and clean).

The issue is now as follows.

Programmer comes on for water or heating, 3 port switches to the correct side, pump is permanently running. boiler acknowledges that there is demand and the fan kicks in. Electrodes spark as they should. Here is where the problem now lies as "sometimes" the boiler will try 5 times and then lockout, sometimes it will fire up first time, sometimes it tries once or twice.

My gut feeling is the solenoid on the gas valve is being dicky, or the Ignition PCB has an intermitent fault anyone else have any ideas?

Customer is also asking, due to the age of the boiler and possibility of other future issues, is it more economical to replace the boiler with something like a Viessmann Vitodens 16KW open vent?

Regards

P>S I have submitted my gas safe number to Harvest Fields so I can post in the private section.

 

[AMGasServices]

did you clean the condensate sump?

 

[Lee Davies]

did you clean the condensate sump?

AMG I did, it was full of the aluminium/carbon from the system, the entire condensate trap is now cleaned.

Can't be this though anyway surely, as the boiler would not get to ignition if locked out.

 

[Burger]

Have you checked standing and working pressures? Could be water in the line.

 

[king of pipes]

Could be repaired but go with your gut feeling the solenoid is easy enough to check , PCB probably around £100 but in all honesty I would be pushing them towards a upgrade , and a service plan which they have neglected by the deposits you have found in the condense trap it wont be aluminium in there as the heat ex is stainless on these. Kop

 

[ShaunCorbs]

Test the gas valve eg put meter on inlet and turn the gas off if the manometer drops it’s working but if it starts doing what you say and doesn’t drop gas valve could be at fault

So test if it’s gettinh the call voltage if not pcb

But tbh new boiler good choice on a 100w

 

[townfanjon]

Test the gas valve eg put meter on inlet and turn the gas off if the manometer drops it’s working but if it starts doing what you say and doesn’t drop gas valve could be at fault

So test if it’s gettinh the call voltage if not pcb

But tbh new boiler good choice on a 100w

No gas safe badge mate , is it on its way ?

 

[ShaunCorbs]

No gas safe badge mate , is it on its way ?

It is

 

[Lee Davies]

No gas safe badge mate , is it on its way ?

If you mean my GSR badge I have given my details to admin via pm WEEKS ago, I sent it to Harvest Fields today so hopefully he can help out.

Test the gas valve eg put meter on inlet and turn the gas off if the manometer drops it’s working but if it starts doing what you say and doesn’t drop gas valve could be at fault

So test if it’s gettinh the call voltage if not pcb

But tbh new boiler good choice on a 100w

Can't believe I didn't think of that earlier.
Thanks again.

 

[townfanjon]

If you mean my GSR badge I have given my details to admin via pm WEEKS ago, I sent it to Harvest Fields today so hopefully he can help out.



Can't believe I didn't think of that earlier.
Thanks again.

No problem pal , hes a bit slow sometimes lol

Here comes the abuse