Discuss Glowworm Hive Upgrade in the USA area at PlumbersForums.net

Messages
3
Hi,

I have a glowworm systempro programmer installed using climapro rf thermostats

I’m wanting to upgrade the system to hive.

There is no wiring centre as everything goes through the systempro programmer.

will I need to rip this all out and start wiring from scratch in new wiring centre before connecting the hive controllers?

the programmer is installed in the airing cupboard next to the dhw tank with the motor operated valves .. boiler in the garage a fair distance away.

I was hoping I could still use the old programmer as a kind of wiring center.
 

Attachments

  • C3BBC73B-807B-4D69-AE60-1571C2B1555B.jpeg
    C3BBC73B-807B-4D69-AE60-1571C2B1555B.jpeg
    586.3 KB · Views: 22
  • D2AD94F9-8D02-4DDE-A858-D030D6BC9E77.jpeg
    D2AD94F9-8D02-4DDE-A858-D030D6BC9E77.jpeg
    250.3 KB · Views: 18
  • FB1B7A00-C05F-401F-AD1A-0C73A12B0AC3.jpeg
    FB1B7A00-C05F-401F-AD1A-0C73A12B0AC3.jpeg
    314 KB · Views: 17
  • FEBB9BF7-F70C-4058-94B5-FFA92ABB1030.jpeg
    FEBB9BF7-F70C-4058-94B5-FFA92ABB1030.jpeg
    391.8 KB · Views: 18
  • D0EE60E0-04A2-4AC0-93D1-BE4F46BDC955.jpeg
    D0EE60E0-04A2-4AC0-93D1-BE4F46BDC955.jpeg
    361.1 KB · Views: 21
It looks quite complicated to m. The motorisedvalves aren’t connected via grey and orange, just have live and neutral to them? The room thermostat would be changed from ebus to mains voltage, losing money saving control there.
 
Yes on the existing set up, there was no orange and grey wires used for motorised valves.

I’ve had nothing but problems with the climapro remotes, losing signal and batteries die all the time, that’s why looking to change it out.

I’m thinking it’s a big job, prob too much for a DIY project though.

I think it will need a new wire centre, once the old programmer comes out and then from there wire in to the hive controllers.

I already started and have wires everywhere.

What have I done hahaha
 
Just going to update this post. Anyone out there who has a similar system and thinks it’sa quick fix to change to hive similar product.. please know this is a big job.

I had to rewire the heating after removing the systempro unit that has all the motorised valves going to it.

I bought a salus tc100 wiring centre from screwfix (not expensive), then had to rewire the whole thing following the supplied wiring diagram (s-plan). Then had to change wiring in the boiler from 24v ebus supply to 230v.

All good in the end, I wish the salus tc100 had come with a wiring diagram for 2 zone plus the hot water .. it caused some confusion but got there in the end with a bit of help from google.
319B799C-6EC5-4A89-B322-810E0B10C41D.jpeg
C3EF280D-F857-48FF-950F-369DBCD0E1D0.jpeg
2C6FC115-5DAF-4A7D-A237-E7F5643DB2F2.jpeg
 

Reply to Glowworm Hive Upgrade in the USA area at PlumbersForums.net

Similar plumbing topics

I have a home with an oil boiler in a garage turned into a flat, heating both flat and main house, running c plan with two pumps, two motorised...
Replies
0
Views
423
J
Hello, I’m hoping someone can help as I’m getting differing advice every time I speak to Vaillant; We are refurbishing a property and installing...
Replies
2
Views
2K
Hi all, new owner here looking for advice ... There is a Grant Euroflame 70/90 oil-fired boiler with two pumps but no motorised valves. I assume...
Replies
11
Views
2K
Objective: I have an existing s-plan plus (see below for details) heating and hot water system, with 2 independent heating zones. There is a...
Replies
1
Views
3K
Hi all, I’m not a plumber but looking to change my parents Dial Thermostat & potterton programmer to a Honeywell wireless type . They currently...
Replies
4
Views
2K
Back
Top