Dear all,
We were disconnected by our gas supplier. We have no managed to find the money to clear the bill. They have told us it will take 10 days to reconnect us.
There is a vulnerable old person in the house and we have no heating or hot water. Also we are worried that the pipes will freeze...
Hi All, what's the cost of a service for an unvented system ? (valiant boiler & mega flow cylinder).
I was charged £320.00, for the following:
Boiler service - no parts changed.
Change wireless thermostat (honeywell to Tado), I supplied the thermostat starter kit.
is that about correct ?
Also...
Anybody bought an anton pro2 to replace a v2. The gas sniffer has a different connection. Can you get an adaptor to make fit or is it another £70 to anton?
Am I the only one struggling to find appliances' manuals online? I know it's hard enough with cookers and old gas fires but I've just been unable to find the manual for an Ideal Exclusive. I thought I had found it but it turns out the GC number was different.
Given the law says "refer to MI"...
What are engineers opinion on Intergas, I've installed a couple of these boilers for people and so far I've been impressed with them. They are a bit clunky and heavy but for the kW you get a lot of hot water and they appear to be pretty reliable.
Just want to know what other engineers think of...
Hey folks,
I'm in a bit of a pickle trying to set up my hot water and central heating systems. Got a gas boiler with a pressure tank and a motor circulating the hot water. There are two wall-mounted time adjustment thingies—one for hot water and heating, and the other for the motor. Oh, and...
I'm looking at the above, hoping it will be a good all-purpose tool for repairing our 2 megawatt furnaces. I'm a bit unsure if I need any of the options on it, I don't want to overcomplicate things, but don't want to miss anything out
I want to use it for pressure testing and leak testing too...
I wish to add a second boiler to my existing meter. Location 20m away. Underground run. Can l use 32mm yellow pipe with copper tails at each end. Thank you in advance
Hi all. I hope you are well. Need some advice on this boiler and fault. E229. Went there and condensate was totally blocked so cleaned it and still not fixed. Then serviced it and still got the fault. Called up worcester and one says its the gas valve as it is making a 3 whoosing noises while...
My first thought when I heard this fault a combi boiler with hot water but no heating. Was a problem with the stat, controls not making the call for heat. If this is not the case. Can the divertor valve be the cause of the issue?
If doing safety checks on a new oven. You check the fsd on the hobs are operating within 30seconds. Are modern ovens now mainly thermo electric? Not a bellows thermostat where you test it lights on low flame then high.
I am troubleshooting a gas hob where one burner is reluctant to light. When it is lit and I blow the flame out the FSD on that burner cuts off immediately, whereas the others take 5-10 seconds as normal. I have tested the thermoucouple for continuity and also some sort of mV output (when held...
Hi guys
Do you bother trying to repair hobs these days or just advise to replace?
Family members hob is constantly trying to ignite.
I dont do a lot gas these days since leaving my last employer.
Hi I am a newly qualified gas engineer in Norwich and looking to gain some experience by working alongside someone. I am happy to travel a reasonable distance. Any advice would be gratefully received. thanks
We have a situation on our allotment where we have a large propane tank (free standing) inside a portacabin (not chained) connected to a plaque heater (outdated flexible hose) which is laid on its back (on the carpet) to serve as a burner to boil water for tea and to heat the portacabin. What...
I've got an inset fire which is slightly too big for the opening - the seals can't press against the front.
How can I reduce the opening by a couple of cm either side? I think just mortar/fire cement won't be strong enough as the seals will be pressing against it. The mortar may crack too...
Just a quick question on common ducts for gas laundry appliances. I have recently looked at a gas ironer which shared a common duct with 2 electric dryers. I believe this isn't allowed but the manufacturer sais it's up to a risk assessment. Any ideas anyone.
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.