Search the forum,

method

In mathematics and computational science, the Euler method (also called forward Euler method) is a first-order numerical procedure for solving ordinary differential equations (ODEs) with a given initial value. It is the most basic explicit method for numerical integration of ordinary differential equations and is the simplest Runge–Kutta method. The Euler method is named after Leonhard Euler, who treated it in his book Institutionum calculi integralis (published 1768–1870).The Euler method is a first-order method, which means that the local error (error per step) is proportional to the square of the step size, and the global error (error at a given time) is proportional to the step size.
The Euler method often serves as the basis to construct more complex methods, e.g., predictor–corrector method.

View More On Wikipedia.org
Recent contents Top users
  1. J

    Shower tray installation: Easiest method of fitting

    Hi guys Just looking for advice on how to make the installation of a 1200x800 stone resin tray easier. I'm fitting a tray into a space with three walls, so obviously space is minimum. The last time I did this I rigged up a pulley from the ceiling joists to raise and lower the tray into position...
  2. I

    method statement

    hi there, i have started my gas engineer course and so far really enjoying it, pipe bending and soldering are a little messy 😆but i got material to practice at home so hopfully neaten all that up. We have been asked to write a mission statement for tightness testing but the instructor hasnt...
  3. D

    CONCERN AROUND PLUMBING METHOD

    Hi, my bathroom fitters installed this plastic pipe as a feed to the new radiator, i'm slight concerned because it is bent over the wooden beam and at a strange angle. We're having a tiled floor so i'd hate for a leak and have to rip up the tiles. Can anyone advise whether this should be cause...
  4. S

    Cast iron soil pipe jointing method

    Evening all, I’ve been asked to replace a cast iron stack on a listed building. The customer has ordered the required materials, I’ve just got to install it. What’s the modern day method to seal the joints? Thanks
  5. GQuigley67

    Generic Method statement/Risk Assessment

    anyone got any for central heating/gas work ?
  6. P

    When is a room air vent for flame effect gas fire really needed (with BS)

    Some history is that one gas engineer (who checked safety after fitting of a new gas meter) in the past said I had to have an air vent fitted in the lounge as gas fire required it, but then another engineer (British Gas) said if it is 7½ bar & below this is not necessary, so blocked the said up...
    • PB108
    • Thread
    • air air vent another british engineer flame gas gas fire method needed really vent
    • Replies: 2
    • Forum: Plumbing Jobs | The Job-board
  7. jonnyswamp

    Template for method statement etc

    Anyone know where I can down load some simple and short templates for scope of works, method statement and risk assesment Connected a kitchen sink to a mains supply and a lift pump for the waste in an office block in Cardiff amd the building owner wants the above Nothing mentioned to me by the...
  8. Riley

    What would be the preferred method here

    I have been asked to look at a botched combined main for a block of flats It would appear that good intentions started but it has been cocked up by the installing plumber Basically it's 6 Flats over three floors. Two flats on each. Incoming mains has been upgraded to 63 mm. I wish I'd...
  9. V

    Method statements

    Is there online generic method statements I could use for maintenance purposes :) or am I gonna have to write them out :, ( Any help please
  10. Jay The Plumber

    Bending offsets - your method

    right, when I'm bending offsets I make the first angled bend, usually 45 degrees then I measure from the straight end section across the distance of the offset I require, then I add an additional 20mm and mark the pipe around. then Its back into the bender to make the offset, I lower the wheel...
  11. A

    removing limescale best methods

    whats the best method to remove limescale build up out of a hot water cylinder had a santon direct unvented cylinder today, managed to poke out 2kg through the hole left when i removed the drain off valve. took ages and was only about a third of what was there i'm hoping one of you is going to...
  12. R

    latest scamming method?

    jist recieved this email, anyone else had it?:thinking: We were unable to contact you...
  13. M

    Method statement for unvented cylinder

    I need to write a method statement for unvented cylinder installation anyone done one or got any ideas, when it comes to paperwork I'm fecking clueless so any help would be appreciated:blush5:
  14. woodsy

    New method of boiler hanging

    Went to service a boiler and the following was found. Yes that is a carpet gripper fixed to the wall with the boiler jig wired to it
  15. E

    Method statement and risk assesment

    Anybody got one of these I can blag please? Lost mine in the changeover onto my lovely shiny new computer.
  16. L

    Boiler sizing

    Hi all was just wondering how everyone sized there boilers.... I normally do combis on hot water flow rate and conventional boilers/hw cylinder on whats already there (if customer is happy with the output of the existing one then why not) there are a lot of methods but was just wondering what...
  17. A

    Method and risk assessments?

    Hi we have won a new build site of a small block of flats, we have a first on site meeting soon and need to bring a risk assessment and method statement does anyone know of a good template I can work too or any advice? also any knowledge of employers liability insurance? Thanks
  18. A

    Method statements and risk assessments?

    Hi we have won a new build site of a small block of flats, we have a first on site meeting soon and need to bring a risk assessment and method statement does anyone know of a good template I can work too or any advice? also any knowledge of employers liability insurance? Thanks
  19. I

    Copper bending methods?

    Hi all, I learnt some copper bending methods on the olci course and I've forgotten them and getting access to the course material is impractical at the mo. been searching online but havent been able to find those actual methods. Does anyone have a link to them by any chance I was wondering? Been...
  20. M

    method statements and risk assessments

    lads. i starting to subcontract plumbing and heating work and require method statements and risk assessments could you send me any information or examples you have to my email address [email protected] thanks for the help guys
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock