You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
flow
Flow (stylized as flOw) is an independent video game created by Jenova Chen and Nicholas Clark. Originally released as a free Flash game in 2006 to accompany Chen's master's thesis, it was reworked into a 2007 PlayStation 3 game by his development studio, Thatgamecompany. SuperVillain Studios developed a PlayStation Portable version of the game in 2008, and PlayStation 4 and PlayStation Vita versions in 2013. In Flow, the player navigates a series of two-dimensional (2D) planes with an aquatic microorganism that evolves by consuming other microorganisms. The game's design is based on Chen's research into dynamic difficulty adjustment at the University of Southern California's Interactive Media Division, and on psychologist Mihaly Csikszentmihalyi's theoretical concept of mental immersion or flow.
The Flash version of Flow received 100,000 downloads within its first two weeks of release, and had been played over 3.5 million times by 2008. Its PlayStation 3 re-release was the most downloaded game on the PlayStation Network in 2007 and won the Best Downloadable Game award at the 2008 Game Developers Choice Awards. It was nominated for awards by the Academy of Interactive Arts & Sciences and the British Academy of Film and Television Arts (BAFTA). Reviewers praised Flow's visual and audio appeal, but noted the simplicity of its gameplay; several considered it to be more of an art piece than a game.
Hello,
First post, be gentle! Anyway, here's my issue. I have a Roca The Gap D-Trit close-couple toilet with integrated macerator in my secondary bathroom. In all it's a great solution for a problem location for a bathroom. However, the cistern has a typical european style side inlet pipe, and...
Hi. Just got a new Worcester Bosch 28cdi. The central heating temperature control will only turn clockwise from the "e" point which is 62 degrees to the maximum which is 85 degrees. It will not turn anti-clockwise from the "e" point to decrease the temperature. The manual says the "e" point...
Hi, Solar thermal not so big these days but a couple of Q for anyone who still works in it.
Background. I'm an Electrician not a plumber.. I've been maintaining my otherwise excellent solar thermal (Original install MCS by Others), for the last ~ 18 years, over which time I've needed to clean...
Hi, first time plumber and poster here.
I've installed two new zone valves and replicated the direction inwhich the original valves were installed. I'm really confused now as I think the originals may have been installed the wrong way round.
The Grundfos pumps' arrow is pointing down whereas my...
Seems strange and I may be reading the MI wrong but i dont understand how the return pipe seems to be hotter than the flow.
I have a Vailant EcoTec 438 conventional condensing boiler.
Here's a photo of the install. You can see the plumber put a Magnaclean on what i thought is the return flow...
I’ve a Megaflo system with a conventional boiler, and yesterday, with no warning, it stopped passing any water.
The cold flow is fine, there’s only the tiniest trickle from the hot taps on the lower floors, nothing on the higher ones.
I’ve checked the combination valve for blockages, and...
Hi Guys
Not sure if this is the correct area to post?
Firstly, i'm not doing this work myself but I need to get a question answered as it impacts an outdoor kitchen slab i'm going to pour and need to run pipe or conduit under it.
Having a commercial LPG griddle installed on the outdoor...
After balancing the flows, one of these blighters has started to drip very slowly from under the red cap. It feels loose to turn, so I suspect the seal around the spindle is to blame. It won't be 'worn' as such, as they don't get fiddled with for years, but this tiny adjustment was seemingly...
Hi there, I was wondering if you set a boiler flow temperature at lets say 50 degrees and your unvented indirect cylinder is at 55 degrees - is it the case your cylinder will never reach up to temperature, or will it reach the temperature but just take longer? I have an older boiler where I can...
I have a single pipe system retrofitted to a 1930's house. It is powered by a condensing gas boiler.
As expected, the radiators get cooler the further they are from the boiler.
It occurred to me that if I fitted a "crossover switch" between the punp and the radiators I could send the water...
Hi there, I have the following system boiler setup with a low loss header and four different circuits. I've set the boiler flow to different levels between 65 to 70 degrees but the surface temperature readings never seem to reach much above 55 degrees into the LLH - I have tried a clip on...
Hi all,
I've had a WB 8000 35kw boiler installed today and was searching through some websites which talked about range rating your boiler and/or turning down the flow temperature to save on cost. I spoke to the engineer that installed it and he advised against rage rating saying that having 17...
Good morning. We have a 10 year old Ultracom which now very frequently thinks there's a demand for hot water, even though there isn't, so the boiler kicks into that mode, and sits there heating tap water that isn't going anywhere. Sometimes this happens if a cold tap has been used or the loo...
Renewing 17yr old Gloworm combi boiler, running dom h/w and 15 rads, 40% are doubles. Water flow from stop valve has been measured as 6L p/m, is that enough to run system effectively?
two storey house with vented system and baxi boiler. Have had the BAXI engineers to fix a slight leak on boiler but when they tried to fill the boiler there was no flow . They think that the cold water feed is perhaps blocked with sludge although this enters the 22mm return flow just after the...
I have a water pipe (unpumped) from a stream in to my shed that houses a water tank. I require a continuous flow of water along pipe A in the photo. At the tee junction water can also be fed in to the tank, pipe B.
I want Pipe A to run continuously (it heads straight in to another stream) but...
Recently had a repair done on a leaky tap they replaced the tap valve on my bathroom 1/4 turn taps, now the hot tap flow is slower
What my problem please and what could I do to fix? They is no areiator on my taps
Hello,
I'm a fairly adept DIYer but I have an issue with my plumbing and not entirely sure what's left to check.
I have an unvented indirect system with 1 hot / 1 heating zone, cylinder is a Range Tribune HE 150L pre-plumbed.
For quite a while now I've had a problem where after the hot water...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.