You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
degrees
An academic degree is a qualification awarded to students upon successful completion of a course of study in higher education, usually at a college or university. These institutions commonly offer degrees at various levels, usually including bachelor's, master's and doctorates, often alongside other academic certificates and professional degrees. The most common undergraduate degree is the bachelor's degree, although in some countries there are lower level higher education qualifications that are also titled degrees (e.g. associate degrees and foundation degrees) and higher level (e.g. undergraduate master's degrees).
Hi,
In a typical household hot water boiler, how long does the water stay at max temperature with no more electrical energy going into it?
Please state this for different boiler sizes?
Assume properly lagged etc.
Vented system, Worcester Bosch 30CDi, NEST control.
Radiators not getting hot, or takes hours.
Wanted to ask if below is a good indicator of a technical problem, rather than looking for blockages etc etc.
The boiler is cycling from 45 degrees, climbing quickly (a degree a second) to 50 where it...
I have a Draper 34212 lever bender. I know it isn't a Hilmor but I don't bend 3/4" much so it does the job. The one thing that is difficult is bending 180 degrees. Do you guys have any tips? Obviously I can do two 90 degree bends with a gap between but often I need a 180.
I was thinking of...
good evening ,looking for some assistance, i have a vokera linea 28 combi boiler running on LPG. problem which has just recently started is that the boiler will run until it reaches 57 degrees and then it cuts out.
It will restart when it has cooled down and then it will cut out at 57 degrees...
Guys,
Apologies if this is a stupid question but I wanted to check something before doing something wrong.
I have an intermittent problem with my HSA3 three way actuator. Intermittently it will fail to turn the boiler/pump on when the room stat calls for heat only (it always runs fine when...
mr_mf
Thread
again
attach
danfoss
degrees
position
question
replacing
spindle
units
Hi, I asked this some time ago but never got to the bottom of it. Is it normal for a combi to give out hot water that is much hotter than the temp set on the boiler and then reduce down? It starts off cold for a few secs, rises to about 60 degrees quickly and then levels out to the correct...
ma701ss
Thread
boiler
degrees
hot
hot water
hotter
thermostatic
water
Hi - I have a bedroom where the radiator is either blazing hot or cold. It is fitted with a TRV (I have tried several different ones to eliminate the TRV as the issue). When the TRV is set to "0" the radiator remains cold. At all other settings the radiator gets hot and stays hot even when the...
jranger
Thread
cold
degrees
either
hot
other
radiator
radiators
temperature
trv
valve
Hi, I recently replaced the battery in my Danfoss TP5000 Si thermostat and now the temperature's stuck at either 8 degrees or 15 degrees and it won't respond to me turning the temperature up or down, it's like all of the buttons have stopped responding. Any help and advice much appreciated!
greysoon
Thread
danfoss
degrees
not working
problem
thermostat
working
Hello, this weekend our Danfoss TP5000 Si digital thermostat started acting weird - automatically setting the temperature to 30 degrees C no matter what we set it to
I noticed the low battery icon was flashing so replaced the batteries
Now it is stuck at 8 degrees C, and the up and down...
Hello there, I'm hoping to get some advice about my heating system. I have a Baxi Bermuda Back Boiler. Installed in the early 80's so pretty old but still going strong! We have always found that our hot water is very hot and the pipe in the airing cupboard coming from the tank is too hot to...
Joebananas
Thread
boiler
degrees
engineer
hot
hot water
radiator
radiators
water
I can't get my head round the best way to complete this job. Picture hopefully added. I have to fit a radiator on the right hand wall but the existing radiator pipes on the left have to remain in place as they feed a bathroom radiator. My issue is how to tee off the exising pipes and run a flow...
Just fitting a Geberit back to the wall frame and noticed the top fittings are helpfully going to join the wall on a mortar line.
Anyone see an issue with rotating the fitting through 180 degrees to get what will hopefully be a more secure fitting as per the image?
Cheers
Had a new Worcester Bosch 38 CDi fitted today. The installer ran the boiler through it's start up process and ran the boiler at a temperature of 90 degrees for nearly an hour. I was a bit shocked at this and was expecting the central heating system to blow up at any moment as we would normally...
Minty!!
Thread
boiler
degrees
installed
new boiler
oil
system
temperature
tested
Hi, I'm new to this forum and have an issue with my Ariston CLAS HE boiler. When both heating and hot water are set to off the boiler is still active and fires on for a few seconds till the temperature indicates 79 degrees or so (pump not running). The burner then goes off and the temperature...
Hi I'm Kash and im new here - looking for some advice/help.
I'm sorry that my first post is one seeking help and not a general hello!
I'm not too clued up so thought i'd post on here to get some feedback. I've used the search function and tried a few things but it hasn't seem to have done the...
Specifics: new boiler, old house thermostat (15 years), old heating system (baseboard pipes, came with the house).
My mother-in-law has a problem which I'm not sure is a problem. Specifically, the thermostat is supposed to keep the house above 60, but she has seen it as low as 55. Now, it...
Unregistered
Thread
after
comes
degrees
dropping
heat
house
problem
system
thermostat
Apologies if this has been covered before but I searched on "Telford" and saw nothing. This relates to events 12 months ago when we had a problem but I never resolved it to my satisfaction so I thought I'd run it past the brains trust:
We have a horizontal Telford Tempest 150ltr being driven...
Hi from a new member and thanks for taking the trouble to read this.
Problem is that the water has not been heating. Inspecting the MA1 actuator shows the black lever firmly in the H sector and I assume it should go to either the M or W when the cylinder thermostat is demanding. I flipped off...
Peaky
Thread
actuator
degrees
drayton
ma1
mixer
mixer valve
movement
problems
valve
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.