Search the forum,

Cement-like substance surrounding shower valve

Discuss Cement-like substance surrounding shower valve in the Plumbing Jobs | The Job-board area at PlumbersForums.net

K

Kaptain-Plastic

Messages
3
Hi

My shower has a very very slow leak from the valve area that is showing up on the other side of the wall to which the valve is installed. I have carefully removed the tile surrounding the valve and found the entire area enclosed in some fibrous, cement like substance. I've attached some photos. The dark area on the bottom left is wet from the leak and is flaking off, while the rest is pretty solid. Does anyone have any idea on what this "filler" substance is, and the best way to get it off?

Cheers,
KP


20180828_105246_small.jpg
20180828_105257_small.jpg
 
Hi all thanks for all of your suggestions and sorry for the late reply. It struck me that given the age of my property, it might be worth checking the stuff for presence of asbestos - it only cost a few quid and would give me peace of mind even though the guy taking the sample thought it was highly unlikely. So I am awaiting those results before proceeding.

Having had a bit of a further dig into the hole, I think the fibres are to do with pipe lagging/protection. I'm hoping the bits that aren't water damaged are easy to scrape/chip off, will let u know. It's just strange that the water was able to "melt" whatever it is.
 
If that fibre burns, it isn't asbestos. I suspect you'll find the pipe is wrapped in felt pipe lagging to prevent the copper coming into contact with the mortar. To be honest, the plastic fitting suggests it isn't all that old.

How much did the sampling and analysis cost, out of interest? Was that the person taking the sample AND sending it off, or did you have to take the sample and post it?
 
Hi the asbestos tests came back negative, so I started scraping at the cement/mortar to get to the leak. The wet bits just fell off, the dry bits were still soft enough to scrape away. All it took was a half turn of another plastic connector on the elbow joint (not visible in the photo) to stop the leak. I'm just waiting for the wall the other side to dry out so I can redecorate. I also need to figure out whether I need to fill what I've scraped out before re-fixing the tile, and what product to fill with - any thoughts from anyone?

The testing was done by a friend-of-a-friend at mates rates, so I've been lucky on that front at least!

Thanks to all here who replied with suggestions/advice.

KP
 
Kaptain-Plastic said:
Hi the asbestos tests came back negative, so I started scraping at the cement/mortar to get to the leak. The wet bits just fell off, the dry bits were still soft enough to scrape away. All it took was a half turn of another plastic connector on the elbow joint (not visible in the photo) to stop the leak. I'm just waiting for the wall the other side to dry out so I can redecorate. I also need to figure out whether I need to fill what I've scraped out before re-fixing the tile, and what product to fill with - any thoughts from anyone?

The testing was done by a friend-of-a-friend at mates rates, so I've been lucky on that front at least!

Thanks to all here who replied with suggestions/advice.

KP
Click to expand...

You should probably replace the washers prior to covering back over, just because you have the opportunity to now and probably won't ever want to open up the tiled wall to gain access again. I also tend to use wras approved medium lock sealant on fittings that are 'buried' as it stops them coming loose, and under compression compensates the washer seal just in case it doesn't seat perfectly.

Personally I would frame the fitting with timber and put in a piece of water resistant plasterboard to cover the valves and allow for re-tiling. If you use stainless screws you can then gain access again in the future by removing the single tile again, and unscrewing the board. Far less hassle than digging filler out :)
 

Reply to Cement-like substance surrounding shower valve in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

C
Mixer bar fitting solutions?
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
0
Views
117
ChrisGid
C
johndave
Outdoor stopcock doesn't fully close
Hi all I'm hoping someone can shine a light on this for me Since our stop tap on the pavement has now been filled with sand for whatever reason, we are relying on our property fitted stopcock (this is outside on our garage wall) Unfortunately turning this to the closed position only reduces...
Replies
3
Views
176
exedon2
exedon2
W
Outdoor Tap at Porch
Hi, basic question, any insight much appreciated. Looking to have an outdoor tap in my front porch fed from 15mm pex coming up from suspended floor. Pic 1 is inside porch, pex temporarily clipped to give an idea of pipe placement (ignore shoddy blockwork of booted cowboy builder!), Pic 2 is...
Replies
6
Views
203
Dave Moore
D
dreikher
Hole in copper pipe, solder under floor, T coupling & protection
I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
122
dreikher
dreikher
D
Covering shallow sewer pipe under concrete Patio
Hello all, I’m replacing a concrete paving slab patio in the back yard. The original patio used 50mm deep concrete slabs on hardcore & sand. I’m planning to pour a 100mm deep concrete patio on 100mm hardcore. In order to achieve the same final height to line up with the rest of the patio, I...
Replies
5
Views
139
DIwhYdidIstartThis
D
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock