Search the forum,

Stumped and doesn't know how to open gph dual push plate cistern

Discuss Stumped and doesn't know how to open gph dual push plate cistern in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Sleekarleng

Sleekarleng

Messages
5
Hi Everyone! My name is Steph and I have been searching hi and low for knowledge on how to open my cistern. No button plate looks like mine and I'm kinda stuck. Please help me if you recognize it!

Thank you!

15609864990053244725942250604705.jpg
 
The problem is I doubt anyone here has seen that design, I certainly haven't. That means there's a risk of breaking it when trying to figure out how it comes apart. That said, with you taking responsibility for the thing if it goes wrong, one or both of the buttons will likely just be clipped in and should pull out. Give it a squeeze and a wiggle and pull to see if one will come loose. Then there may be a screw or clip underneath that you can get at to go further.

Good luck, don't pull too hard!
 
Stigster said:
The problem is I doubt anyone here has seen that design, I certainly haven't. That means there's a risk of breaking it when trying to figure out how it comes apart. That said, with you taking responsibility for the thing if it goes wrong, one or both of the buttons will likely just be clipped in and should pull out. Give it a squeeze and a wiggle and pull to see if one will come loose. Then there may be a screw or clip underneath that you can get at to go further.

Good luck, don't pull too hard!
Click to expand...
Thank you for this! I will be gentle!
 
Stigster said:
The problem is I doubt anyone here has seen that design, I certainly haven't. That means there's a risk of breaking it when trying to figure out how it comes apart. That said, with you taking responsibility for the thing if it goes wrong, one or both of the buttons will likely just be clipped in and should pull out. Give it a squeeze and a wiggle and pull to see if one will come loose. Then there may be a screw or clip underneath that you can get at to go further.

Good luck, don't pull too hard!
Click to expand...
Yes!!!!! I did it! Thank you! Both buttons come up and there is one screw underneath. Whew! Hooray!
 

Reply to Stumped and doesn't know how to open gph dual push plate cistern in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

jamespipe
Plumber recommendation for heat pump HWS installation
Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't rip me off? An office guy recommended me to apply for government rebates and get it installed through timetosave.com.au. How reliable is this...
Replies
4
Views
169
oz-plumber
O
Stigster
Does anyone know the name of this model of Roca toilet?
Hi guys. I'm trying to identify a toilet model before ordering a seat for a customer. I went to what used to be a Roca stockist (they no longer are) and one of the guys there reckoned it might be "The Gap". I went to the new stockist and the guy there disagreed it was "The Gap" and that he'd...
Replies
2
Views
111
Stigster
Stigster
sammie81116
Sewer pipe problems not sure about it
Hi all Noticed bad smell in my drain out side put my hand down and it unclogged it for now however I checked my sewer drain and after flushing my toilet a good few times nothing is going to the sewer so don't know is there a blockage or what way it works many thanks and advice would be grateful
Replies
3
Views
356
Chuck
C
B
What is correct toilet supply line
Hi. I need a new toilet supply line but don’t know the size type of the fitting at the shut off valve. It is not 3/8 compression. It is a plastic nut about the same size as the one going into the cistern but has a different thread. Attached is a photo. Can you advise. Thanks.
Replies
2
Views
167
ShaunCorbs
ShaunCorbs
F
Mystery Mira Elite QT Leak
Hi All I have a leak coming from within my Mira Elite QT shower. It seems to be flowing from behind the switching Control. Any ideas what could be causing this leak. Already Changed the Pump Elbow as one of the clips had popped which was causing a second small leak, Any idea? Is it time to buy...
Replies
0
Views
202
Firefox
F
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock