Discuss Incoming mains 3bar flow rate 16litre permin in the Plumbing Jobs | The Job-board area at PlumbersForums.net
Rob Foster
Esteemed
- Messages
- 2,083
3 bar at 16 litres per min is very good. When did you test this ?
I would be careful ...in high summer or peak morning times it may well be less. What times did you sample ? Where about s are you .we will all move nearby eg ..London the water crawls out if the pipe and tastes uck and still has female contraceptive pill residue in it
Rob Foster aka centralheatking
I would be careful ...in high summer or peak morning times it may well be less. What times did you sample ? Where about s are you .we will all move nearby eg ..London the water crawls out if the pipe and tastes uck and still has female contraceptive pill residue in it
Rob Foster aka centralheatking
- Messages
- 34,309
- Solutions
- 2
Storage combi at min something like a Viessmann 111 or 222 best option is an unvented cylinder
North Scotland 25 mile from inverness
Tested 0815
Rob Foster
Esteemed
- Messages
- 2,083
08.15 on a Sunday ? I would do it again on a weekday morning about 07.30 hopefully you will get same result Rob Foster aka centralheatking
No room for unvented without major alterations
Don’t suffer electric power cuts here
Rob Foster
Esteemed
- Messages
- 2,083
Also this sounds like a rural area, there might be an area pump set that kicks in during the day. If you want to really check see what it’s like in the dead of night when a local pump set might be timed off .
Chking
- Messages
- 7,272
Intergas ecorf 36
Rob Foster
Esteemed
- Messages
- 2,083
No Riley, area pumps are usually off until 5.00am to save lecky and reduce pressure in main and leakage when system in low demand. In my village the lights used to flicker when the thing started up around 5am Centralheatking
- Messages
- 10,855
I meant the opening question
Rob Foster
Esteemed
- Messages
- 2,083
Sorry ok and yes it has often several times per month chking
Not Sunday Tuesday
not out in the sticks, just good scottish mains water and a good water board
Reply to Incoming mains 3bar flow rate 16litre permin in the Plumbing Jobs | The Job-board area at PlumbersForums.net
Similar plumbing topics
Hi All
I have a leak coming from within my Mira Elite QT shower. It seems to be flowing from behind the switching Control. Any ideas what could be causing this leak. Already Changed the Pump Elbow as one of the clips had popped which was causing a second small leak, Any idea? Is it time to buy...
Hello,
I am seeking some advice, I have a POTTERTON PROMAX 28 COMBI Boiler and I noticed yesterday that the water around the house is no longer warming up. The heat exchanger has been changed 6 months ago, so I do not believe it is that. Does anyone have any ideas on what it could be?
Thanks
Hi,
I have an old steel water mains pipe (approx 45mm) that I need to connect to a new pehd water mains (25mm). I can't get at it to create a new thread so what's the best way of connecting the two?
Cheers,
Peter
We run a community village hall and have a large kitchen provided for the use of hirers. This includes a Lincat SLR9 gas cooker which I believe is a 23.8Kw appliance with all six burners and oven on max. This was installed some 10 years ago and has passed all subsequent Gas Safety inspections as...
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking?
This originally happened about 12 months ago and has happened 3-4 times since.
It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Creating content since 2001. Untold Media.
Newest Plumbing Threads
-
-
-
What constitutes a Commercial Appliance and thus a Commercial Kitchen?
- Started by FozzieBear
- Replies: 3
-
POTTERTON PROMAX 28 COMBI Boiler - Hot Water Issue
- Started by boiler101
- Replies: 4
-
Hole in copper pipe, solder under floor, T coupling & protection- Started by dreikher
- Replies: 0
-
-
-
-
-
-
-
-
-
Sewer pipe problems not sure about it- Started by sammie81116
- Replies: 3
-