Search the forum,

Discuss soft jaw grips/similar in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

helpsy

Plumbers Arms member
Plumber
Gas Engineer
Messages
1,754
Where is the best place to get a decent pair of soft jaw grips please?
 
Never seen them in my local parts centre or City’s a plumbing mate. (Sorry) I’m sure @ShaunCorbs will pop Along shortly with a link for a supplier.:p:p
 
Depends what your going to be using them for, if your only going to be using them on spanner flats / nuts then go for the knipex pliers wrench

If your going to be using / wanting the grip function then go with the soft jaw ones but they won't grip like normal grips

Also I wouldn't go with anything else other than knipex I've got a set 10+ years and there still going strong

Knipex 86 03 300 Pliers Wrench Adjustable Spanner 300mm | eBay

Knipex 81 11 250 Soft Jaw Plastic Traps Tube Fittings Connector Gripping Pliers | eBay
 
Depends what your going to be using them for, if your only going to be using them on spanner flats / nuts then go for the knipex pliers wrench

If your going to be using / wanting the grip function then go with the soft jaw ones but they won't grip like normal grips

Also I wouldn't go with anything else other than knipex I've got a set 10+ years and there still going strong

Knipex 86 03 300 Pliers Wrench Adjustable Spanner 300mm | eBay

Knipex 81 11 250 Soft Jaw Plastic Traps Tube Fittings Connector Gripping Pliers | eBay
For chrome nuts and shower items that are round
 
It will have to be the more rounded shaped soft grips then. I suppose you could have that and a Knipex parallel jaw wrench.
Plumb center were once doing the Knipex parallel wrench at good price, that was posted about on here. Otherwise shop around or try online to avoid high cost.
Note that the Knipex is made in various sizes. I have the 250mm I think, and it has max opening of jaws of 2 and a 1/4"
 
Status
Not open for further replies.

Reply to soft jaw grips/similar in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Copper pipes, I think its fair to say, is not what it used to be, the copper is getting thin while the cost is going up. Meanwhile, plastic Pushfit seems to be getting better and better, cost and convenience was always better, but now the quality is to, have we reached a stage where plastic will...
Replies
2
Views
176
Hi, I have an old steel water mains pipe (approx 45mm) that I need to connect to a new pehd water mains (25mm). I can't get at it to create a new thread so what's the best way of connecting the two? Cheers, Peter
Replies
2
Views
159
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
0
Views
115
My son has an apprenticeship interview for to become a plumber and heating engineer. The have said there will be a multiple choice exam for this for suitability. The thing is my son panics during tests/exams. Is there any book I can buy him to practice the multiple choice test for the exam? What...
Replies
3
Views
356
IS IT POSSIBLE TO ADJUST THIS MIXER UNIT? WE HAVE TO HAVE IT TURNED ALMOST FULLY ANTI CLOCKWISE TO GET HOT WATEROUT. THE FRONT PLATE WITH MIRA ON IT PRISES OFF AND INSIDE THERE ARE SOME PLASTIC BITS AND A SMALL CROSS-HEAD SCREW IN THE MIDDLE. THANKS
Replies
6
Views
196
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock