Search the forum,

Discuss Difficult tap head removal in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
W

Woodro92

Hi guys,
Having difficulty removing this tap head to replace the washer.
No visible seam to remove the cap looks like a one piece but I can't be sure.
Any advice on what to try.
 

Attachments

  • 1475422567597-1230385780.jpg
    1475422567597-1230385780.jpg
    84 KB · Views: 42
As above
It's usually the very top above the 2 bands.

Turn anticlockwise, with palm of hand pushing down on it.
 
Thanks guys it must be incredibly tight as I can't un-screw it no matter how hard I try, I'll have to pick up another strap spanner to attack it from 2 sides
 
I dont think its the top 2 bands , its the very top before the "bands" start
 
Yes, as above, the dome part.
I would suspect turns and unscrews. It is possible that it just pulls off. Go easy though.

If all else fails, I find throwing myself face down and having a temper tantrum can make me think better.

Have you tried warming the top with hot water ?
 
Try whacking it gently with something that won't scratch or dent it, - like a rubber mallet.
Then top tip is clean the little top dome well and use electrical insulating tape all around it quite lumpy to allow you grip with your hand.
Failing that then just persevere with a strap wrench.
I use silicone grease on their threads later so someday it might come off easier
 
Try whacking it gently with something that won't scratch or dent it, - like a rubber mallet.
Then top tip is clean the little top dome well and use electrical insulating tape all around it quite lumpy to allow you grip with your hand.
Failing that then just persevere with a strap wrench.
I use silicone grease on their threads later so someday it might come off easier

Whack it gently ?

That just made me laugh out loud !

Rest of advice is brill as usual 'best' but, I don't know how you whack something gently ?
 
Whack it gently ?

That just made me laugh out loud !

Rest of advice is brill as usual 'best' but, I don't know how you whack something gently ?

Lol! I knew it sounded wrong!
What I meant was hit it a fair whack, but not as hard to break the basin, or the power you would use to whack your wife. :smile:
 
Lol! I knew it sounded wrong!
What I meant was hit it a fair whack, but not as hard to break the basin, or the power you would use to whack your wife. :smile:
Ah ! Now that's cleared it !

I fully understand. Thank you. Lol
 
Just to be clear, - on a Whackometer scale of 10, it only needs a 5.5.

Ha ha, excellent.
I'm glad you've referred to the plumbers whackometer scale of belting things about.
I was thinking with the 'hit your wife power', comment, it might be nearer 6.25 but you cleared it up for me.
 
Status
Not open for further replies.

Reply to Difficult tap head removal in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

I need to replace the washer of my kitchen mixer tap as it is leaking. I was able to remove the spout once by unscrewing the screw on the back of the tap. However now I can't remove it again as it seems I must have used the wrong screw head and have rounded off the head. Please see attached...
Replies
9
Views
375
Hi, My Blanco Kitchen Tap Model Swift BM1420 is leaking. Please see attached photos for details of where water leaks from. What I've done so far. I replaced the cartridge. Leak persisted. Bought some replacement seals and tried to put in place of the old ones. Here's what I did next. Remove...
Replies
2
Views
182
Have a sink basin tap photo attached and need to replace the heads as behind they have cracked. Any idea where I can get replacement tap head covers only need to change the tap head covers really Problem is the old tap head covers wont turn! Any ideas please? Thanks
Replies
0
Views
240
  • Question
Hello I have a Franke Planar Kitchen tap and it’s got a leak. One drop per minute. I’ve been on YouTube and seen that there are grub screws to remove, first for the handle, then once that is off the square piece between the handle and the tap body to get the cartridge for replacement. I have...
Replies
1
Views
136
Hi, I was hoping someone might be able to help with this. The tap is a Bristan RS BAS C, the hot tap has been leaking and I've trying to get the tap off to clean the cartridges, but cant get the sphere at the end off there. Looking at the diagram, it seems that you should be able to pop the...
Replies
9
Views
371
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock