loctite 55 as thread sealant

[greekengineer]

Hello to all engineers,what is your opinion with regard to using loctite 55 as thread sealant?
LOCTITE 55 – Thread Sealing - Information & support - Loctite

 

[ShaunCorbs]

very good also 577

 

[greekengineer]

I have still not used this product,and I am curious about its ability to seal the components - parts.
Usually I prefer loxeal 55-14 with no worries at all.
http://www.loxeal.com/wp-content/uploads/2017/09/TDS-55-14e.pdf

 

[Pickwickpick]

very good also 577

Do you use it in place of ptfe tape?

 

[greekengineer]

If you watch online videos,the company suggests that loctite 55 should be used alone without any additional substance.
That is my worry,can this product offer a viable and permanent solution ?

 

[Pickwickpick]

Didn't mean whether it was used with ptfe, was wandering what context it would be used in.

 

[king of pipes]

Use it alot in place of ptfe good for cylinder fittings rad tails still get ptfe though . Kop

 

[Pickwickpick]

Really like the couple of different types of loctite I've used for various things on the bike and and on the Bedford, looks like found new use for it then!

 

[Welder]

Loved it. Far better than straight PTFE

 

[townfanjon]

Ace stuff , havnt used PTFE for years

 

[rpm]

Use it and the tape for different applications, used the liquid 577 then known simply as threadlock on metal threads but the joints must be clean and oil free for it to cure.

 

[WC1]

Always been straight ptfe but often wondered about the loctite. Any one say why it might be better than ptfe on some application ? Thanks. Wc1

 

[ShaunCorbs]

It's the best

 

[Stigster]

Always been straight ptfe but often wondered about the loctite. Any one say why it might be better than ptfe on some application ? Thanks. Wc1

I have found it to be more reliable than PTFE on radiator tails especially and also more reliable on fittings in the sizes above 3/4". I'm not sure why it works better but it does in my experience!

 

[rpm]

It's the best

too busy to give a full answer, no worries stigster did it for you

 

[ShaunCorbs]

too busy to give a full answer, no worries stigster did it for you

Don't know what other I could of add other than try some

 

[gmartine]

Always been straight ptfe but often wondered about the loctite. Any one say why it might be better than ptfe on some application ? Thanks. Wc1

55 does allow for some adjustment when PTFE leaks.

 

[WC1]

So you can back the fitting out a bit?

 

[gmartine]

Exactly

 

[WC1]

Great, I'll give it a go. If I'm gonna try something that could cause a leak in a customers house, I need to know why I should try it. Thanks

 

[DXCross]

Definitely +1 for loctite. The newer shaped containers with finger imprints are a god send.

 

[gmartine]

 

[apcdave]

it's great ..... you won't regret trying this stuff... seriously the best

 

[Last Plumber]

I use it all the time and have stopped buying PTFE tape as much because this does a better job.

 

[Deleted member 96286]

I use Flomasta Pipe Thread Sealant from Screwfix on outside taps to wallplate elbow connections. It's the next best thing to welding it on, it's that strong. Using this on the threads eliminates the need to line up the wall plate elbow with the tap using a wrench as it can be turned to whatever angle you want and left for an hour to set. It won't move again and is fully watertight. When replacing outside taps, I usually replace the wall plate elbow as well so the fact that the tap can't be removed isn't a problem. To use it, I coat the threads of the tap with a zig zag line all the way round with the Flomasta and apply a ring inside the wall plate elbow. Screw both of them together to whatever angle you require, wipe off the excess and sit both on a kitchen towel for an hour. It won't come apart again.

 

[greekengineer]

After having used loctite 55 , I must report that this product gives the impression of a perfect sealing.
The tip is that you must cross - crossing the tape on the thread.
I ended up on the loctite 55 after having failures with the use of ptfe. Especially when I used ptfe on short adds on (photo below) or parts with short thread.
I noticed that loctite 55 offers a better solution .

 

[64degrees]

Ain’t used PTFE for years - normally scratch up the thread a bit to give it a bit of adhesion, another vote for loctite 55!

 

[Pickwickpick]

Ain’t used PTFE for years - normally scratch up the thread a bit to give it a bit of adhesion, another vote for loctite 55!

What do you mean by scratch up? As in like keying in with some wire wool/wet&dry/emery or something else? Have never used loctite 55 but think will give it a try after all the recommendations in this thread.

 

[gmartine]

What do you mean by scratch up? As in like keying in with some wire wool/wet&dry/emery or something else? Have never used loctite 55 but think will give it a try after all the recommendations in this thread.

See the vid in my earlier post, loctite recommend keying quality metal threads when using 55

 

[Ben-gee]

First got loctite 55 for dual fuel t-piece / element, which have a nasty habit of ending up in the wrong orientation otherwise. Now I use it for all rad tails, outside tap, shower outlet... etc It’s much better than ptfe!

 

[ShaunCorbs]

What do you mean by scratch up? As in like keying in with some wire wool/wet&dry/emery or something else? Have never used loctite 55 but think will give it a try after all the recommendations in this thread.

Cross cut a hatch pattern with a pair of grips or hacksaw blade

 

[WC1]

Got some 55 today, tiny little roll, I'll have to make sure I don't get it mixed up with my toothy floss!!
Also after spending decades generally preventing damage to threads, deliberately scratching up the thread is gonna take some getting used to. But overall looks good, thanks guys!!

 

[Ch4 plumbing]

Use miles and miles of the stuff, brilliant on threads up to 2"1/2 but got to be carefully any bigger then that as it can run up the thread even when you have scored them.

 

[WC1]

Aaah.. is that what the thread scoring is all about? - stopping it running up?

 

[ShaunCorbs]

Yes