Search the forum,
Questions and plumbing advice in the Bathrooms, Showers and Wetrooms - .

Some popular plumbing forums: Plumbing Advice - Plumbing Tools - Plumbing Courses & NVQ's

Forum Prefix Filter

Hello, I need some advise, will greatly appreciate if someone can help. My mixer tap is leaking from base want to renew it. However the tap cold/hot water feed is connected via connectors/fittings as shown in attached picture. Can anyone please advise how to disconnect tap from these fittings as...
Replies
3
Views
457
L
Hi all Does anyone know where i could get a replacement upper roller pulley for my Elegant Shower please? Part No 0045-5 I have emailed the company several times with no reply, i have called them 3 times to be told someone would call me back. I was eventually told on my forth phone call that...
Replies
2
Views
342
Is this new shower tray defective and would you install it in this condition? The void where the wax deposits were (last photo) is between 4m-6mm deep. TIA.
Replies
3
Views
479
C
Hello, I'm wondering if you can help me. I have an insurance company who is trying to get me to make my plumber re-quote for work to replace a broken bath. He's included a bath panel with the quote as it's the type of bath that requires a panel (and the original style is not available so can't...
Replies
2
Views
376
I've just replaced an Ultra SASF2 – M thermostatic shower cartridge together with the spring mechanism and the temperature sensor. My problem is this: If I install the thermostatic cartridge together with the spring mechanism and the temp sensor (i.e. do the job properly), the shower runs warm...
Replies
0
Views
532
I'm attempting to replace an ultra SASF2 – M thermostatic shower cartridge but, having removed the temperature control knob from the housing that incorporates the temperature 'stop' mechanism, I cannot pull this housing free from the rest of the assembly. I can see no circlip holding it in...
Replies
9
Views
803
For the guys doing a lot of bathroom work. What dual mixer showers would you recommend? I don’t think the budget reaches to the Grohe stuff but also want something that’s not going to need new cartridges every 5 minutes. Cheers
Replies
8
Views
726
Hi All. My Aqualisa Aquavalve enclosed mixer shower valve leaked and gave way and I am looking to replace. I am looking for recommendations what model would I replace it with and how would I replace it if I changed the model! I would like to change the type of model to a lever one. I have...
Replies
0
Views
392
Hi folks As mentioned in the title, are there any solutions to the problem, other than cutting an access to waste pipe and cutting pipe at nearest elbow or tee? Hair has been removed as much as possible and a drain cleaner used but still very slow to drain. I’m not keen on strong chemicals...
Replies
4
Views
413
D
I’m wanting to replace the single handle cartridge on my basement shower since it no longer allows hot water (sink in same bathroom works fine). I have turn off the water main (at the sidewalk), cold water intake to water heater and opened up all other faucets in the house. However, the shower...
Replies
0
Views
308
DIYSAM
D
I have just moved into a flat and the water waste pipe from the flat above goes through our bathroom. And the water comes into room. I call the flat owner to say my problem but he don't interest him. I am there to find a talented plumber. Please reply me.
Replies
1
Views
354
Hi, I have a few issues with my bath drainage and leaking. The first issue is that the near corner of the bath by the taps is sloped downwards meaning that it pools in the corner and quickly starts leaking through gaps in the shower screen onto the floor rather than into the bath. The rest of...
Replies
0
Views
307
My plumber fitted a shower, 2 of the walls are glass panels and one is a tile board (wedi board). He joint the wedi board pieces (3 pieces) close to each other but didn't use any joint sealant. When I asked him whether this will be an issue for future leaks he dismissed it. How worried should I...
Replies
1
Views
453
We've just had a new bathroom fitted but noticed a few annoying scratches on the polymarble top, central on top at the front of the basin. Plumber has tried 'Bar Keepers Friend' to remove it but it's unfortunately taken the gloss/shine off the area and we're left with just a dullness where the...
Replies
2
Views
644
Hi everyone. I'm installing a walk in shower, opening into shower will be on right, mixer value on right, but shower head and drain on left. The pipe work from the shower mixer valve is exposed silver colour pipework. the pipe work will run up from the valve then take a hard left at the ceiling...
Replies
9
Views
1K
Hi all, this might have been asked many times before, so apologies. Just moved into a new housebuild and the bathroom tiling is not good! What would you say ix the largest gap to fill with silicone? It's obvious that the tiler has cust his tiles to short and it trying to hide this with...
Replies
3
Views
413
Hi am wondering if I can get some advice on this issue. Shower was working fine until Saturday when the dial only works when turned to cold water side and hot water side doesn't work. Other shower works fine and all taps have hot water coming out. Just wondering if get some on advice on what...
Replies
1
Views
471
Most grateful for any advice on the fittings reqired to enable 22mm feeds into the mixer taps via the chrome extension pipes customer supplied in a kit with no instructions. The taps are 'Homes 1924 Bathrooms' This is a free standing kit. There chrome pipe is 35mm internal with a detachable...
Replies
2
Views
380
Post a New Thread / Question
Creating content since 2001. Untold Media.
OFFICIAL SPONSORS

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock