Questions and plumbing advice in the Plumbing Tools - We also have a popular tiling tools chat, and a electrical tools talk forums..
Some popular plumbing forums: Plumbing Advice - Plumbing Tools - Plumbing Courses & NVQ's
Evening all,
IYHO which is the best plastic / mlcp pipe cutter (not for waste pipe).
Cheers
Jim
Hi.
I've recently purchased a press tool which is branded geberit but it's actually a novopress aco 103.
I was wondering if anyone knew if there was an adaptor that would fit so I can get the machine in tight spaces. I know Rems do a 45° attachment but not sure if this would fit in my...
View: https://www.youtube.com/watch?v=i3ae5gPyLhQ
I like it...needle bearings everwhere, less stress on the hands, rock hard cutting wheel + spare, one size required and no pipe deformation.
Hi All
I'm after an inspection camera, there has been times when I've needed to look down a drain, or check a leak under a shower, or look under a floor for a pipe run, seen chap ones which attach to your phone, but I suspect these might be rubbish, endoscopes are not long enough.
There is...
hello all
I am looking at getting my kit started as my boss has given me loax Ash and I have some. Does anyone have any tips on wefd to head to looking at all hand tools and power tools so was hoping to get a good deal thanks
After not doing plumbing for alot of years my tools could probably do with an upgrade eg my bacho 10,12 inches open about as wide as a 6inch wide jaw now.
I see the armeg jaws for taps so probably going pick up them.
Also see knipex adjustable wrench that looked good.
Any tool ideas to make life...
I bought these (not the ones in the image, what they sent) Ratchet Tool for 0.5mm²-10mm² Ferrules - https://www.tlc-direct.co.uk/Products/DVDCER510.html, however I had to return them as the crimps kept getting stuck, nearly broke the wire getting it out. I was considering these Ferrule Kit -...
Hi all. I hope you are keeping well.
I just had all my hand tools pinched from the side door of a house as I was packing up. Probably about £300 worth. Is it worth claiming on my insurance or as it is only £300 just pay for new tools. Would my premium go up that much is basically what I am...
hi chaps - thinking about investing in one - not sure to go rothenberger or arctic products...any suggestions? pros and cons? much appreciated! thanks dave
currently an apprentice and just changed over some basin taps my tap spanner isn’t great and slips off a lot, can anyone recommend anything decent and not too expensive?
thank you
https://www.completecareshop.co.uk/personal-care/hand-sanitisers/antibacterial-hand-gel-pump-bottle-triple-pack
Hi guys had to open a new account not sure what happened to my old one.. Is there a drill pump out there that can pump up my 1st fixes for pressure tests? As doing it by hand can take a long time. Thanks.
Hi guys just wondering is there a drill pump or something that I can attach to pressure test when I'm on new builds. Currently using the rothenberger pressure test pump but that can take a while to get up to pressure pumping by hand. Thanks guys.
How long do they normally last...changed the batterys but mine still churps away over an opened gas hob as if there's no leak (after calibration).
well thought I'd try one - thinking would enable me to remove nozz without touching the electrodes - its a Regin and pretty rubbish as the inner spanner fits the nozz snugly enough but the outer is too big for the nozz holder.....ah well ..what a waste
Hi,
I after opinions on which M Class dust extractor is better for coreing holes when using a dust extraction adaptor. I have narrowed it down to either the Bosch GAS35 AFC or the Metabo ASR35.
Any one used them both?
I'm trying to find a spindle pin for this bender. This is the 19mm pin which goes through the quadrant bit then the bender frame, the bending arm, and out the other side. Irwin UK have told me this is only available as part of the quadrant assembly (Part No.T220H in their catalog, or part H in...
- Question
Replacing 15 x stopcocks @ 22mm thought I'd try cutters as usually I pull 'em and space was tight.
These Ox brand 22mm cutters just deform the olive and score the pipe.
The jaws don't close properly as witnessed by the burr where the handles meet (pictured) preventing cutting of the olive.
Cost...
-
- Question
Replacing 15 x stopcocks @ 22mm thought I'd try cutters as usually I pull 'em and space was tight.
These Ox brand 22mm cutters just deform the olive and score the pipe.
The jaws don't close properly as witnessed by the burr where the handles meet (pictured) preventing cutting of the olive.
Cost...
Creating content since 2001. Untold Media.
Newest Plumbing Threads
-
What constitutes a Commercial Appliance and thus a Commercial Kitchen?
- Started by FozzieBear
- Replies: 3
-
POTTERTON PROMAX 28 COMBI Boiler - Hot Water Issue
- Started by boiler101
- Replies: 4
-
Hole in copper pipe, solder under floor, T coupling & protection- Started by dreikher
- Replies: 0
-
-
-
-
-
-
-
-
-
Sewer pipe problems not sure about it- Started by sammie81116
- Replies: 3
-
-
-