What's with the lack of sds max adapters for diamond cores.
I see countless sds plus bits as well as sds plus to keyed chuck adapter but I can't find any sds max bits.
Any one any ideas
Hi, does anybody know what gas is in the freeze master's pipe freezing units, mine could do with a check and a top up. My local aircon branch said they might be able to re-gas the unit if it contained a gas they had. Thanks in advance.
Armeg jaw droppers. I hears good things and I like a new toy. But both the machine screws on one of them that hold the sliding jaws wouldn't bite and stay in place - no matter how hard I tightened them. Resorted to a fibre washer.
Hopefully things will improve.
Didn't get the nerrad as too many...
Hi to all member
I want to post this product I bought some weeks ago in a website in GB, it is called Acqua Tempus
apparently it is very simple but it is not: it is a shower timer with shut off; it is programmable and has a lithium battery that gets charged with the passage of water, son I do...
I'm thinking of getting a Stud Finder, so that when I drill or nail something into a wall at home, I don't puncture any pipes, wires etc.
I heard that cheap ones aren't good, not sure if this is true.
Any recommendations would be very welcome 😉
Hi guys looking at upgrading the van and am looking at putting some sort of inverter set up in place. Now I know nothing about these other than I know pure sine is less likely to damage whatever is plugged in. Does anyone have experience of these at all?? Literally JUST looking at it recharging...
Hi
I’ve purchased a basin mixer tap for my bathroom.
trying to install the tap and can’t find a tool to fit the nut that holds the tap in place. I’ve tried one of these and it doesn’t fit. To small.
https://www.NoLinkingToThis/p/basin-wrench/13294
I’ve got a diagram of the tap, need to know...
Is there anyone out there recognise the manufacturer of the shower mixer valve , there is no markings on the leaver or brass work. It has started to leak around the barrel. Thanks
I need to replace 13 TRVs due to sticking issues, I saw that Honeywell do a tool to remove and exchange the TRV inserts', this will save me draining the system and saving time, anyone know where I could hire one from?
Cheers
Yes I know topic has been covered umpteen times but here is another. Has anyone experience of the Rigid 32573 supposedly goes from
6mm up to 28mm? Only asking as a bit fed up with my Kopex ones, I only do a bit of DIY cutting but have 3 sizes 15,22 and 28. The 15mm is shot
the 28 is plastic and...
So it is time for me to scrap my vivaro which has just be written off my the insurance company after someone crashed into the van while parked. Lucky as I was just going to dump it this yr any way. Will be sad as have had it for 12yrs.
Any way, need to get a new one which complies with euro 6...
The drain cock on my water cylinder is very close to the ground and is obscured by piping installed by the previous owner. The spigot is at the bottom but, try as I might, I can find nothing to tighten it. Can anyone offer any advice ? Thanks
Hi everyday peeps,
I need to correct a mistake in the heating system in my dad's flat which has two radiators connected with flow in at bottom and return from the same end at the top. Nothing wrong with TBSE in the right setting, but best not to have the flow and reversed messed up!
Easiest...
I'm looking for a quality robust sealant between rubber bathroom flooring and sanitary ware as well as gap filling between floor and skirting, it's not a wet room but needs to go off hardish and be easy to clean. Does CT1 fit the bill?
Hi everyone,
I am going to change the tap in my bathroom, is it quite straightforward to change a single lever tap, do I need any specific tools or should I get a plumber in to do the job, thanks.
Hi all,
I'm a novice so go easy ;-)
I have a Rothenberger SuperFire 2 torch and would like some advice as to how to safely remove the tip from the gas canister as it is advised to store them separately when not in use? The advice slip says when storing, turn the control knob to the ON...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.