Ermm I'm a TADO virgin so be gentle with me. What black magic is this, how tf does the wireless stat talk to the boiler when there's no receiver in the starter kit?
Hey,
I'm a new entrant and I've just completed my 2 year training course and have my final week gas assessment next week. I was just looking for some advice on what I can expect? (I'm not asking for answers or cheat sheets, just what the final assessment week intales so I can be best prepared)...
I do this quite a bit but just wanted to check with you guys and see where we recon I stand if it goes wrong.
I quoted for boiler replacement without upgrade of gas supply to 22mm and quoted separately for upgrading pipe 'if required'.
When commissioning I dumped the digital gauge in favour of...
Can someone tell me what is the correct or legal requirement for us gas engineers if we are fitting a new boiler or doing anything to the gas line and find that the meter has an Anaconda on both inlet and outlet ? Is it a legal requirement for us to change it or what category would it be given...
Just had a call from my 94 year old aunt (lives on south coast)
Today had a annual gas service. Many years ago very large room dividend in two plastered stud wall pair of doors in middle doors never opened (but could be)
Gas fire in each room, engineer has disconnected one fire saying you...
My testo 300 today when commissioning a new install would only give a reading of 21.3% o2 for flue integrity, tried zeroing outside but stayed at 21.3 tried turning on and off still the same. When in the flue gas test port it would go down to what you would expect and 5.3. Anyone have any ideas...
I currently work in an office job on mid 20's salary and hate being chained to the desk.
Looking for a career change to become a gas and heating engineer.
I have came across various courses which offer retraining such as the below...
Hi all,
Just had a Navien NCB 40kw combi installed by an approved fitter. The DHW rates of the boiler seemed promising on paper - 16.4lpm at a 35 temp rise and 22.9lpm at a 25degree rise. More than adequate for what we need. The only issue now its installed is that I'm not getting any more than...
Evening
I've not posted for a while and have had to set up a new account as I can't find my old one.
Moving on I have a wiring conundrum.
Customer called said heating had died no lights on programmer. At the property the customer also asked if I could change the honeywell wiring centre...
I wish to add a second boiler to my existing meter. Location 20m away. Underground run. Can l use 32mm yellow pipe with copper tails at each end. Thank you in advance
Hi All,
This is a bit of a random one, but I'm a product designer working on a lighting project and I'm on the hunt for unused/waste/offcuts of the 60mm plastic flue inner that you get with some boilers.
If anyone in the Glasgow area has any of the white for translucent stuff, I would...
Gas fire manufacturers state final connection to the 8mm service valve must be by using rigid copper pipe. R250 presumably not wishing to reduce diameter when using soft copper with inserts. What is the availability of this pipe as few plumbing outlets appear to have it.
Hi,
I have a newly installed boiler which has built-in frost protection, when the installer installed this boiler, they did not disconnect the old external frost stat which is still wired to the boiler.
I assume no newly installed boiler is still wired with old external frost stat, right? So I...
I am going back to a Worcester Greenstar 30 CDi Classic that's failing a CO2 emissions test on minimum rate only. I do adjust the gas valve but there is zero effect. I haven't mixed up the "min" and "max" adjustment screws.
What could be causing this boiler to fail on minimum only? It's perfect...
Looking for a gas safe engineer to complete a boiler and cylinder install in Ringwood BH24. There was a delay of approx 8 months from the install to radiators being fitted and therefore able to comission the system. Our plumber is now employed elsewhere and unfortunately unable to complete this...
HI there.
Just wondering if anyone knows whether it's possible to access British Standard documents through BSOL(British Standard Online) at home? If so how much is membership?
If no, then which libraries offer access to these documents? I'm based in London.
It would litereally be several...
Hello everyone.
My first post here, dont know if its in the right area, sorry if its not.
Im doing the ACS gas with Access Training, they provide live and recorded seminars for the theory, but i find it difficult to understand, im not blaming them because even in the book (Niceic) its hard to...
Hi guys. Do any of you guys know of any training centres in the West Mids or close to Stratford upon Avon? I was hoping to get into Swat gas but they’ve ran out of spaces.
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.