Questions and plumbing advice in the Gas Engineers Forum - This is a PUBLIC Gas Engineers Advice Forum..
Some popular plumbing forums: Plumbing Advice - Plumbing Tools - Plumbing Courses & NVQ's
Forum Prefix Filter
]Hello all
Having checked with Gazco spares , they tell me they dont have a kit of any kind. The gas fire is discontinued.
I am researching the possibility, of converting a LPG to NG (Gazco Riva 67 Pedestal).
Does anyone on here know if its possible to convert a LPG gas fire to NG ?
The...
Anybody else make a non Vaillant facia type receiver 'cept Salus?
Hi when I was servicing BBUs and fires during my apprenticeship there wasn’t a necessity to FGA them back in 2004. I always serviced them by stripping down and cleaning, perform smoke bomb tests, controls check and spillage.
I know you can FGA the boiler at draugh divertor but what do you do...
Hi all,
We want to change the position of our boiler from the Kitchen to the outside cupboard at the front of the house.
The cupboard is 1m x 1m and 2.4m height and currently has a wooden door - so temperature wise will be close to outside temp.
We want to install a Viessmann Vitodens 100-w...
Hi can i get some advice, does the facia and soffit of the house class a eave, as the flue coming out of the wall is more then 200mm from the eave but only 20mm away from soffit and facia. Would it still need to be a distance of 200mm or would it be 75mm same as guttering and drain pipes...
I'm due to fit my first gas fire (been servicing them for a while, but not yet fitted one). The previous fire's 8mm pipe runs from the right hand side of the chimney opening. Quite possibly, the new fire will take a side entry pipe. However, I'm curious - if I need to re-run the pipe, so it...
Hi, could you help me to solve mysterious stuff happening with Ariston e-combi 38 located on the loft
Can hear the sound of the boiler pump in our bedroom. If I come closer to the boiler, it's not sound so bad, but in bedroom you can hear it a lot.
pump is running even with room stat turned...
Does anybody work with a company offering finance for the customer with regard to new boiler / central heating installation ?
Looking for anyone who has had issues setting up and adjusting a new Honeywell gas valve on a Remeha Quinta Pro90 gas boiler !
Problem is getting the boiler to light as a starting point before adjusting to correct settings
I am currently studying to pas as a gas engineer and I have come stuck on some of The modules and can’t seem to find the answers anywhere.
Q1. A gas meter can be installed without a mounting bracket or support shelf, only when
A1. The supporting pipework either side Is constructed of rigid...
Hi all, I came across some 8mm copper pipe /plastic coated under a gas fire today. I haven't seen this before? Is it OK to be there? (It was put in by a reputable firm local to me, whom I trust, though I'd like to know what it is).
Thanks all,
Jennie
Hi guys any of you lot familiar with these ,
Not firing for hot water at all doesn't even try, had the call brought a hot water flow sensor as it was only pennies saved going back to merchants , no joy ... heating works fine.
Can some one explain to me how the sensor works ( on a blue tab...
An OVO fitter installed a gas meter and said we would smell gas for 24-48 hours. I took a look in the meter box and saw a load of putty and sealant around pipe that goes into the property. Just wondered if this looks like it's been done correctly? Or if we should get it looked at.
Horizontal and vertical flues
Existing installations no clips on extensions definitely AR? Or defect? Bit of a grey area, also self tapper screws? Ar or defect? If flue has neither but is solid would you leave on?
I’m doing a cp12
There is a gas cooker which should have a Glass lid.
There is no lid or mechanism present and the safety device has a Metal plate holing it open so the hob works?
Is this AR or NCS?
My own boiler at home has developed an intermittent fault causing an ignition lock out every week or two when there is a demand for hot water. When reset the boiler runs without issue for a week or two. This fault only occurs on HW demand, there has never been a lock out on CH demand. Ideal tech...
Hi I have a boiler to service - ideal logic plus combi 30kw. Customer says when heating has been on for a while and they he runs the hot water the water is scalding hot.
Anyone have a any ideas? I was thinking maybe thermister on flow?
Anyone fitting these?
Can you pay to extend the warranty to 10 years like Vaillant?
Was just thinking about ways of monitoring heating system efficiency and the effect of different ways of using the house, what doors and windows are open at what times and the effect of various weather on gas consumption. We can do it for electricity at a household level, but it's fairly...
Creating content since 2001. Untold Media.
Tags
Newest Plumbing Threads
-
No Hot water, Fixed and Broken Again Ideal Logic 24
- Started by Filthbags
- Replies: 0
-
-
What's happening to this radiator, paint flaking off?
- Started by mikmikmikmik2024
- Replies: 1
-
Is it necessary to earth bond a Kitchen Sink?
- Started by Cello
- Replies: 2
-
Show us your fanciest radiators you have installed!!- Started by Lou
- Replies: 0
-
Y Plan, no hot water but heating is working when called
- Started by Chopper9495
- Replies: 8
-
-
Towel Rail Valve Advice please (35 Characters needed.)
- Started by NorthernLad
- Replies: 6
-
Unvented discharge at high level current regs
- Started by Matt0029
- Replies: 11
-
Trying to source a dual-flush valve
- Started by Thomas J Marshall
- Replies: 2
-
-
-
-
What constitutes a Commercial Appliance and thus a Commercial Kitchen?
- Started by FozzieBear
- Replies: 3
-
POTTERTON PROMAX 28 COMBI Boiler - Hot Water Issue
- Started by boiler101
- Replies: 4
