Questions and plumbing advice in the Commercial and Industrial Plumbing Forum - .
Some popular plumbing forums: Plumbing Advice - Plumbing Tools - Plumbing Courses & NVQ's
Forum Prefix Filter
Hello all.
I have fitted three new Saracen timed flow valves to existing shower rooms.
But these valves are still allowing water to flow from shower head and won't close off.
I have tried various options and sorted other connections in the shower lines 5 on one line 3 on other. Only 1 new...
Hey, forum friends! 👋 Excited to introduce Master Drain Ltd, your go-to expert for top-notch drain installation and repair services. Here's what sets us apart:
🔧 Seamless Installation: When it comes to drain installation, precision is key. Our skilled team at Master Drain Ltd ensures that your...
Does the evomax lose its settings when power turned off
Hi all,
Hope all are well.
I’m in the early stages of renovating an industrial unit. The fit out is to have 7/8 commercial kitchens, these kitchens will have reasonable output, i.e. high street takeaway in terms of their demand.
The unit has 3 bar of pressure and 25 litres a minute of water...
- Question
I have an Intergas 2030-3 0/0 dual fuel burner; circa 1998, connected to a strebelwerk chamber. The burner hinge had a crack in it and was thrown away. turns out intergas no longer make the part... does anyone know where i might be able to get hold of one?
Hi,
I will try to explain best I can, please bare in mind I am currently in a learning stage so just trying to understand the process behind things.
A building with three floors and 69 rooms. How do you work out the pressure needed on the hot water system? I’m sure there is a calculation to...
Looking at replacing a stainless steel welded 90 metre water system in press fit. Its going to cost about £18k in Mapress but I have seen M-Press are alot cheaper on their fittings. Has anyone got any experience with M-press 89mm fittings. Just wondering if they are cheap for a reason.
Hi all,
I'm on the committee on a community of owners for an apartment complex in Spain. It consists of 130 apartments. We have continual problems of sediment in the incoming water supply, blocking aerator in the taps, filters in shower mixers and even flexible pipes.
It's a common problem...
Can anyone explain this? I had a shower professionally istalled in my en-suite a few weeks ago, as art of a full refurb. We use the shower from time to time but not daily. I was sitting downstairs alone in the house when I heard a loud bang and went up to find the fixed glass of the shower...
My local rugby club are having intermittent pressure drop problems with their showers. I’ve done quite a lot of domestic plumbing but need advice on this. The system is set up with 4 large hot water storage tanks, there are 4 pumps each which have a flow sensors on them. There are 10 showers...
Hi all.
I just wondered whether any of you are currently doing any site work on a price?
Only on the plumbing side no gas. Things like cylinder installs, 1st fixing and 2nd fixing.
I know this will vary across the country, I’m based in the midlands.
Any advice would be helpful.
Cheers
We have a Grundfos for a domestic water booster application. Everything is set up for constant pressure, discharge pressure sensing and all appears okay, except we cant get the motor to run in "auto". We can run in manual at a constant speed, okay. But we try and go to control, the pump will...
We are using a the rigid 65s pipe cutter for the smaller stuff but we have a load of 88.9mm x 2mm stainless coming up and was looking for a decent pipe cutter. Any suggestions?
Hi guys. I’m on a job at the moment where the building has 100 flats over 4 floors. The problem is there’s no mechanical supervisor on site or any drawing in regards to the waste pipe work. One of the issues seems to be, there’s only 5 vents going out to atmosphere. today we’ve been told to run...
I had an electric boiler installed recently which required the boiler to be inhibited by an electric shower. The proposed installer wanted to use a Heatrae Sadia Relay RL1. I stopped this, as an electrical engineer this unit is NOT complaint to electrical regs unless the cables to the fuse...
Looking to replace a faucet with spray hose in a small commercial kitchen. we did have one installed by a plumber a while ago but in all honesty it seemed like a piece of chinese crap off of Amazon. Very similar to the American T&S model. It leaked like hell and after only a couple of months the...
Having a chat with colleagues on this one to decide on best route.
Existing 500L megaflo which does not provide sufficiant HW.
Cold water entering cools the hot way too quickly and consequently the 500L is good for about half that.
Coil is 54kw boiler is 80kw
Cylinder options…
The...
I have a WB 30i system boiler with a Honeywell programmable roomstat in the hallway and a cylinder stat.
With a new double glazed porch, cavity wall insulation and topped-up loft-felt the house must has a high efficiency rating. But….we now live in the ‘Sunroom’ off the hallway and this has DG...
Hello
Can anyone help me identify this actuator head. It’s making noise, heat not passing through ?
I have been asked to fit an external tap at a mental health facility to enable the external paths to be hosed down. What form of back syphoning measure is sufficient for this installation?
Creating content since 2001. Untold Media.
Newest Plumbing Threads
-
Trying to source a dual-flush valve
- Started by Thomas J Marshall
- Replies: 2
-
-
-
-
What constitutes a Commercial Appliance and thus a Commercial Kitchen?
- Started by FozzieBear
- Replies: 3
-
POTTERTON PROMAX 28 COMBI Boiler - Hot Water Issue
- Started by boiler101
- Replies: 4
-
Hole in copper pipe, solder under floor, T coupling & protection- Started by dreikher
- Replies: 0
-
-
-
-
-
-
-
-