Hi All,
I wonder if anyone could give me some advice regarding a Worcester 28cdi ii , I get hot water only at certain times when the central heating is on and even then the hot water is in short supply, there is a tank next to the boiler.
Is there a way of having hot water all time when needed...
Ok, following on from my drain tap thread, does anyone have an opinion about this vibration noise. It started a few days ago there's no lockout or fault code and everything works as it should except for the noise. I fancy it's the pump but as they go for about £150 I want to be as sure as i can...
Hello everyone,
Currently no hot water or central heating with my Worcester 26cdi XTRA.
It's making clicking noises and then a loud scraping noise when trying to ignite.
I've taken a video of problem, any ideas what might be wrong?
View: https://youtu.be/rDk2PxmsXIw
Any ideas of what...
Morning Guys,
I have a Worcester 230 Combi in a rental property that is going to overheat lockout after a couple of minutes on DHW, no issue when on CH but if DHW is called for when heating is on same fault occurs.
System is clean as always had inhibitor so unlikely to be a blocked heat...
boiler works fine for rads and hot water, but after reaching required temp and shutting off a noise continues .. sounds like a fan or air blower. Sometimes stops in minutes other times hours. sometimes doesn't happen at all
I have a worcester 24i boiler i have no room thermostat/programmer, i have to run up and down stairs to turn it on and off, i know i can get a mechanical programmer but i want a wireless units. Is there one for this boiler. Many thanks
Hi, I am new to this forum and was wondering if anyone can help me with recognising this DFE gas fire and locating a manual for it.
I have a Wonderfire Gasflame Special DFE gas fire and need a manual to look at to see the required ventilation for a gas safety certificate. I cannot find anything...
Hi we currently have a Worcester Bosch 550 CDI. I was having issues with it and had a plumber come out to have a look the pump was struggling so that was replaced. The boiler keeps going into a flashing mode where there is a E looking without the top line I have attached a video. The central...
Advice on how to Wiring up a WR1 wireless receiver to a Greenstar 25SI boiler
Have
LR > C on thermostat
Ls > L on thermostat
Ns > N on thermostat
L > L 230 supply
N > N 230 supply
Receiver turns on call for heat receives green light comes on but boiler does nothing … reading online I’m...
Hi Guys.
I have a Worcester Greenstar 30i boiler and when we moved in we had our old Thermostat removed and a Nest installed, I have now removed the Nest ready to put the old thermostat back on (Honeywell CM907) but don't know where the wires are meant to go.
I think I've done the boiler bit...
Hello - I'm a relatively new owner of an old house here in France that was updated by the previous owner who lives in the UK. He used one channel of a two channel Horstmann C27 to control turning on and off the electric water heater. Given that I'm from the states, I'm not all that familiar with...
Hi,I wish to change a 600 switchmaster heating timer with a horseman 425 tiara.i have connected all the wiring as per instructions.i have however noticed a loose yellow wire on the switchmaster,it looks like it should be connected to term 3 . Is this correct. And when I get round to changing...
Hi Everyone - despite my best efforts I can't seem find a clear answer on how to wire a single channel Hive Receiver to a Worcester Bosch Greenstar 4000 30kw. I've attached 2 photos showing the connections on the receiver and boiler. With great hope you experts out there can help - thankyou!
Replacing an Ideal Mexico on a Y plan, fitting a Vaillant pure 425 with VRT 350f. normally have someone else do the wiring but can't attend. Does anyone have any experience having wired up something similar and have diagram please?
Hi all, I have a potterton promax combi boiler with a very basic Neomitis wireless thermostat. If I upgrade to a programmable Neomitis thermostat what are the chances it will work with the existing receiver - I’ve no idea what receiver it is or where it is but it’s currently working.
Hi , My wireless thermostat, has become water damaged and is toast , no longer displays anything (long story), it is a boss
bps242rf and the receiver is a BR1, can anyone tell me if there is just a wireless thermostat (transmitter) that I can buy that will bind to the existing receiver (BR1) it...
I have a Viessmann vitodens 100-w 30kw being controlled by a EPH CombiPack4 wireless thermostat. I need to move the receiver because it is struggling to communicate with the thermostat in the location I want to put it.
Could someone advise on the cable required please? I can see that it's 4...
Hi guys. I have a friend with some holiday rentals. They all have a combi in the attic and a wireless RF stat set up. He’s wanting to make them all so he can turn the heating down after the customer has left from his house using the net. Is there a quick solution or will a cable need bringing...
I'm going replace my Honeywell ST9400C and DT90 for a Honeywell TR6-HW
I've had issues with the DT90 after replacing it for my old Dial thermostat. So thought I'd go back to the ST9400C which is located next to my boiler and wire in the TR6-HW at the old ST9400C location and use the wireless...
I have an ideal combi 30 boiler and I want to install a frost stat Drayton.
I am confused by the wiring because I believe the boiler has no voltage contacts yet all frost stats have 230v. The boiler has two contacts yet the stat has only one switch wire. So confused how to wire up and concerned...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.