You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
quick
QUICK Corp. (株式会社QUICK) is a financial market information vendor headquartered in Tokyo, Japan. It was founded in 1971 as Quotation Information Center K.K. (株式会社市況情報センター), and changed its corporate name to the acronym "QUICK" in 1987. QUICK has four offices in Japan (Tokyo, Osaka, Nagoya and Fukuoka) as well as overseas offices in London and Hong Kong.
Hi,
Hoping some of you folks can steer me in the right direction. I have been self employed for the last 15years supplying services to the industrial gas market. That ranges from installing cryogenic storage tanks, pumps and pipework to high pressure Hydrogen systems and bulk LNG. My work has...
Hi all
I’ve just joined the site as I find myself searching for answers to heating questions and inevitably landing here, reading people’s similar questions and all your helpful answers.
I’m a DIYer with a keen interest in understanding how my heating system works and how it could be improved...
Looking at a particular range (Vernis) of Hansgrohe taps and mixers. A 2 function bath mixer seems readily available but can only find a 1 function shower mixer. I will have a shower head and a separate hand shower so wanted a 2 function setup so I can switch between the two.
Can I use the...
Hi guys. Very specific question...
Got a RAS-C2 where the pin will only move a fraction of a mil and no amount of the usual tapping/WD40 will help. So looking to change the gland rather than the whole TRV.
Has anyone here changed a RAS-C2 gland before? There doesn't seem to be anything to grip...
Hi
Swapping over my kitchen tap, thought would be straight swap but not the case.
Old tap = 15mm copper into pvc/push fitting
New tap = European size Flexi hose into pvc/push fitting.
Now I have the European to 15mm adapter but there is no threaded insert in the pvc for it to grip into.
Am I...
Hi All
Looking to replace this so i have a standard threaded end outdoor tap, looks like they have managed to fit an indoor tap outside as is?
Will a standard 1/2" outside tap like this screw on where the union is?
https://www.NoLinkingToThis/p/outside-tap-with-double-check-valve-15mm-x/37241...
Amazing Chemical Clearance Sale
We are selling off the following Pallets of chemicals reduced to clear
Part Number: C004300
Product: SAFEGUARD EXTRA 200 1 LTR
QTY: PALLET OF 280
Only 3 Pallets left
Only £100 ex VAT each pallet (0.35p ex VAT for each chemical)
Part Number: C004301
Product...
Hello,
We have a pretty standard gravity fed system. Two cold water and one expansion tank in the loft and vented cylinder in the airing board airing cupboard on 1st floor. Pressure is terrible on both ground and first floor so we have a 4 bar pump that blasts both hot and cold water around...
Just wondered if I could have some quick advice re kitchen sink measurement as I want to be sure I buy the right sized replacement sink. I see that sink widths and lengths come in standard sizes, but when I measured my sink it falls between two of these standard sizes - i.e. 98.5cm length by...
I have a 500 litre thermal store serving an old property that we are working through to replace most of the pipework, all of the rusty rads and to integrate a Heatmiser Neo control system with Emetti manifolds and control valves. Some UFCH comes later.
For safety I want to add a pressure...
Just drove 30m to a emergency call out, water through ceiling. The landlords handyman installed a new bathroom last year, silly get hasn’t tightened the hot polyplumb tap connecter. It has a fibre washer... is this normal? I wouldn’t know, as I don’t use plastic.
Thanks
As long as the engine is the same size are all Expert, Dispatch and Scudo's of equivalent shape/year exactly the same and just re-badged? Or is there some skullduggery going on beneath the bonnet between brands?
Thanks
Evening all, I’ve just left my last job of the day and I’m completely knackered. I’ve just been round to a job I did in January ( manual flush radiator on kicrobore) and whilst I was there the old tower mid position valve was making a racket, so the customer asked me to put a new one on(...
Sharp Point
Thread
answer
fault
mid position
please
position
quick
valve
Sure it's been mentioned on here before but does anyone use quick books or anything alike ?
Does it make your life easier and is it easy to pass it into HMRC at end if year
Hi guys, as some of you know my fault finding is pants so just want to clarify something.
Called to another vokera unica today. Fault code 73 relating to return pipe thermistor.
Removing combustion chamber cover and there was a little weep coming from the return pipe connection into the heat...
Hello there guys i just wanted to gets some help. I am a new learner and just started doing my portfolio. Basically i want to find the KW of this cooker DSG60k of its manufacture declared figure
However when i had a look on the data plate it got me abit puzzled. I know its on G20 but next to it...
I know as much as anyone how difficult it is finding a way to gain experience in this industry. My background is fires and fireplaces but I find the work slowing down and want to change over to boiler servicing and breakdowns (ideally contract work)
I live in Upminster and my ideal situation is...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.