Posting a message to the forum will remove the above advertisement

Last Activity:: Jul 15, 2017

Joined:: Jul 13, 2017

Messages:: 2

Trophy Points:: 1

Positive ratings received:: 0

Neutral ratings received:: 0

Post Ratings

	Received:	Given:
	0	0
	0	0
	0	0
	0	0
	0	0
	0	0
	0	0
	0	0
	0	0
	0	0
	0	0

Gender:: Female

Birthday:: Jun 4, 1973 (Age: 44)

Location:: Momouth

Kate0406

New Member, Female, 44, from Momouth

Kate0406 was last seen:: Jul 15, 2017

1. There are no messages on Kate0406's profile yet.
Show Ignored Content
Loading...
Loading...
About

Gender:

Female

Birthday:

Jun 4, 1973 (Age: 44)

Location:

Momouth

Member Type:

DIY or Homeowner
Interact
Content:

Find all content by Kate0406

Find all threads by Kate0406
Tel::

07921780393
Loading...

Latest Threads

Recommended Thermostat Settings
badbnoo posted Sep 20, 2017 at 4:33 PM
Replacement part for push/pull...
Liz posted Sep 20, 2017 at 1:07 PM
paint for copper pipes
Trac posted Sep 20, 2017 at 9:24 AM
Loosening nuts on radiator pipes
Trac posted Sep 20, 2017 at 9:18 AM
COMBI 2 ZONE + UF + EXPANSION...
Just a geez posted Sep 20, 2017 at 12:36 AM
Insufficient clearance around...
DarrylNotts posted Sep 19, 2017 at 10:58 PM
Anybody recognise this...
Fletcherplumbing posted Sep 19, 2017 at 9:23 PM
It is good idea go self-employed
Miro posted Sep 19, 2017 at 8:39 PM
radiator stays on (even when...
Jennie posted Sep 19, 2017 at 8:04 PM
Shorn pipe connector
Will108 posted Sep 19, 2017 at 4:30 PM

- New ceiling light - what am I doing wrong!!! posted by Matt Anssari. Hi all, New to forum, apologies if this is in wrong place. Purchased a replacement ceiling chandler and wired up, but obviously wrong as fuse keeps tripping. I've got the two green wires from...
- Safe fused sour isolation palava posted by Hisham Al-Bizri. hi there guys, I'm a lowly gas man but thought I would put my hand out to you helpful electricians to see if there is a better way to do the following! I work for a rather large gas service and...
- Fault on underground Sub Mains cable posted by kibble19. Hi, I am currently in the middle of completing a new installation in time for a Halloween event at a local activity centre. Over the weekend, while I was not there, it seems that they have lost...
- Testing a socket in the middle of a distribution circuit. posted by Kelsall McEwen. First post. I've installed a 6mm SWA cable to a summer house in the garden from the house. Summer house has a cu with a ring and light. I've installed an outside socket in the middle of the...
- Dimming an Outside LED Light? posted by blindedfox. Hi guys, I am looking at having a outside light installed over a door, the light I am looking at uses a E27 bulb fitment which I am planning to use a LED replacement. I would like to be able to...
- LED Replacement Bulb Issue posted by Darren Nelson. Hi, I have just bought some LED replacement bulbs for our kitchen lights. I have attached 2 images for reference. I was told the replacement LEd would simply replace the standard E14 SES halogen...
- Converting split load CU to Main Switch (RCBOs) posted by Amblik. Hi folks, i have a 16 way British General CU which was configured as split load. I'm converting to all RCBOs which is fine apart from one small detail, i don't have a single neutral bar long...
- Extending sub main cables? posted by Tink666. Hi everyome We're refurbing our lower ground flat within a Victorian terraced house, and there are 2 flats above. Contractor has knocked out all relevant walls and found services running through...
- Testing off-peak circuits during on-peak period posted by SparkyChick. Hi chaps, Just wanted to gather some feedback about this topic. To give it some context, yesterday I went to sort out why one storage heater in a property was on all the time. 24 hour board +.
- Replacing old double light switch with new, odd wiring? posted by jezThomp. Simple back story.. We have a double switch for our bathroom that controls the extractor fan (left switch of 2) and the bathroom lights (right switch of 2). We need to replace it as its bust...
- Good Water resistant thick bed floor adhesive posted by Sam2494. Hi, Currently in the middle of renovating an old property, dug up old quarry's and self levelled! Still out by 10/15mm in spots so looking for a waterproof thick bed adhesive. Needs to be...
- New tools or gadgets posted by Kyle Knowles. Has anyone bought anything good recently I'm at the point where I'm struggling to satisfy my tool addiction at the moment lol
- Why Not Say Good Morning Before Work? posted by antonio. why not say good morning before work? We start Monday? tomorrow x workers :)
- Funniest questions you've been asked by customers posted by Paul C.. People say "Its only easy if you know the answer", or "if you have to ask, its not a stupid question". But surely a line has to be drawn somewhere. On our ebay site we had a customer message...
- Tiling on to painted wall posted by Jamorgan90. hi all, I am doing on a job and just looking for abit of advice. I have a stair case wall to tile in 200x100 what prime would you use? Tile master grip ?
- Would you consider working abroad for a short period? posted by Plan Tec Tiling. As the title says really... Would you consider working abroad for a short period of time? This is not a thread offering work!, just to see what others thoughts or experiences of it are. I...
- Win A Makita Drill With Victorian Plumbing!! posted by Lou. To celebrate [IMG]@VictorianPlumbing 's sponsorship of the UKPlumbersForums.co.uk and TilersForums.co.uk we are giving away a brand new 18v Makita drill to one lucky trades person.. Win A...
- genesis tiger trowel posted by Chris Gibbs. has anybody used one of these things? they state it gives 100% coverage. View attachment 93594
- My builder says epoxy grout too "inflexible"?! posted by Tardigrade. Hello, I'm tiling my bathroom. Rectangular tiles, brick pattern. Most are new stud walls with plasterboard. Floor to ceiling, but not floor itself, and quite a few corners / niches etc. I... My...
- What brand of Tile Cutter do you use Poll 2017 posted by Paul C.. ***I suppose we'll get it but this is not intended for the usual Rubi vs Sigma war.*** I can't find one so am guessing the last cutter poll on the forum was back in 2013 when I was still... What...

Untold Media

Post Ratings

Kate0406

About

Interact

Useful Searches