Search the forum,

Recent content by GH77

  1. GH77

    Gas pressure question

    Okay, that's fair enough ... I feel that the information I gave was a confirmation that his gsr was competent and why ... I don't feel that it informed him how to carry out a working Gas pressure test at the meter and/or boiler as that would be too much information in my opinion... I most...
  2. GH77

    Gas pressure question

    Nothing wrong with healthy debate, nothing wrong with disagreeing with one another so long as there is respect and I said that I respect you Kris ... You've asked if the top of the forum flashing red means rules are being broken? ... and as i'm new to the forum then i'd like to know too ...
  3. GH77

    Gas pressure question

    Same as Shaun, if i've broken any forum rules then I would like clarification from the administration ... unlike Shaun i'm new to the site, so I would like official clarification if i'm in the wrong .... if i am then i will hold my hands up and take it on the chin like a big boy ... i only want...
  4. GH77

    Gas pressure question

    It states the pressures, doesn't state how to carry out the test ... that document is readily available to anyone with access to Google ... i'm now done with this thread ... i'm not getting anti or anything i like your input on other threads and respect you as an industry professional
  5. GH77

    Gas pressure question

    The picture I posted doesn't tell you how to carry out a procedure, it does clarify that what the gsr said about pressures is correct, was used to reassure that the gsr does know what he's talking about ... the common theme on this thread is people continuously stating " use a gsr" and wormwood...
  6. GH77

    PTF Tape and Compression Joints

    If I'm supplying the monobloc then I always look for one with copper tails, not a fan of flexi
  7. GH77

    PTF Tape and Compression Joints

    In my experience what tends to happen is that there is a 15mm ballofix in place as isolation to the tap with 15mm copper running up to the tap rigid all the way with a tap connector on the end... someone wants to replace the tap, they shut off a ballofix, undo the nut and olive then remove...
  8. GH77

    PTF Tape and Compression Joints

    There is no problem if you are fitting a tap flex with a built in isolation valve as you are make a compression joint to a copper pipe... the issue here is joining a tap flex that is designed to mate with a flat faced 1/2" connection, but actually connecting it to a 15mm ballofix valve with the...
  9. GH77

    Alpha he 33 airflow problem,

    Blocked recuperator?
  10. GH77

    Two opinions. Who is right?

    You could try uprating 28mm later in the carcass, but the acid test will be at commissioning when you have the Gas installation at full load and check the inlet working at the boiler, if it's below the minimum the manufacturer allows, what is the gsr going to record on the benchmark? ... there's...
  11. GH77

    Combi boiler replacement?

    Get whoever quotes you for a new boiler to measure it, they will have a weir gauge, be a waste of money for you to buy one though ... if you use an accredited installer they will do a survey and tell you what boiler you need and will be able to explain how they came to that conclusion, standing/...
  12. GH77

    Alpha he 33 airflow problem,

    This might sound stupid, but have you checked the flue terminal? ... i had a similar fault once and the customer had removed an internal door, taken it outside and leant it against the wall inadvertently blocking off the flue, boiler would run with the case off... agree with Shaun about...
  13. GH77

    Combi boiler replacement?

    As others have said, by far the most important thing is a good installation, a good boiler poorly installed will fail ... my experience of wb customer service has been excellent, the vast majority of warranty work has been carried out within a couple of days... even managed to get a free boiler...
  14. GH77

    CO2 is the most important reading not the ratio?

    I had a an Ecotec plus 831 on Thursday that was low on CO2 and Gas rate, I adjusted it until the CO2 matched the mi's, did the Gas rate again and it was within tolerance, CO was below 100ppm if I remember rightly ratio 0.0008, i'm not saying you should adjust, but i made an engineering decision
  15. GH77

    Combi or system boiler

    I like system boilers when fitting a couple of boilers to a low loss header, but the customer needs a big budget for that .... as others say it's about what the customer wants vs what they can afford ... I tend to find flow rate is a biggie, i'll come to customers who have had their cylinder and...
Creating content since 2001. Untold Media.

OFFICIAL SPONSORS

OFFICIAL SPONSORS

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock