Search the forum,

Discuss ELECTRIC boiler needed (- Potterton Gold Electric 12V?) - nr Ashford,Kent in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
N

NEEDABOILER

Has anyone fitted one of these - is it simple? (It is to replace an old oil boiler in a small bungalow)
We have no gas and cant afford a new oil boiler, so this seems the ideal solution, although we realise the running costs are higher.
- is the Potterton 12KW one good?
 
Last edited by a moderator:
Haven't fitted one but removed one for a cust, they were paying £600 a quarter on electric for a 3 bed cottage with a economy 10 tariff.
 
- is the Potterton 12KW one good?

The potterton will probably be a re-boxed version of the Heatrae Sadia Amptec, since they are part of the same group. On that basis, it will be as good as any other - Heatrae are a premium brand in electric water heating.

Running costs really will be hideous though.
 
[DLMURL]http://www.elnur.es/download/manuales/CM%20y%20CMX%20manual.pdf[/DLMURL]
 
Last edited by a moderator:
Haven't fitted one but removed one for a cust, they were paying £600 a quarter on electric for a 3 bed cottage with a economy 10 tariff.

Thanks for your advice - We do have Economy7 and only 4 radiators, all with thermostatic valves, so still think it might be worth a try?
 
The cost difference between a electric boiler and a cheap oil one cant be that great (a quick Google indicates its only a few hundred quid) I'd have though the cost savings of keeping oil would be enough to make it worth while. Or as ermintrude says unless the jacket has gone on your old boiler it almost certainly can be economically repaired.
 
The cost difference between a electric boiler and a cheap oil one cant be that great (a quick Google indicates its only a few hundred quid) I'd have though the cost savings of keeping oil would be enough to make it worth while. Or as ermintrude says unless the jacket has gone on your old boiler it almost certainly can be economically repaired.

- I thought oil boilers were about £1800. I'll have another look thanks - sounds like it's going to be too costly to run on electric only.
 
If the jackets ok a good engineer can get it back to life. Very worst case I would expect a new or recon burner into it.
 
This is just what the forum is all about - an honest question - info given based
on experience and I learned somethings as well - Thank all

centralheatking
 
Status
Not open for further replies.

Reply to ELECTRIC boiler needed (- Potterton Gold Electric 12V?) - nr Ashford,Kent in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

I want to reconnect some outbuildings to an existing water supply. The supply pipe is old 22mm MDPE and buried for a fair distance so not going to dig it up and replace it 😬. Question is can I use normal 22mm plumbing push-fit connectors to make the connection as finding 22mm MDPE fittings...
Replies
1
Views
209
Copper pipes, I think its fair to say, is not what it used to be, the copper is getting thin while the cost is going up. Meanwhile, plastic Pushfit seems to be getting better and better, cost and convenience was always better, but now the quality is to, have we reached a stage where plastic will...
Replies
2
Views
168
Hi. I need a new toilet supply line but don’t know the size type of the fitting at the shut off valve. It is not 3/8 compression. It is a plastic nut about the same size as the one going into the cistern but has a different thread. Attached is a photo. Can you advise. Thanks.
Replies
2
Views
167
Hi, I have an old steel water mains pipe (approx 45mm) that I need to connect to a new pehd water mains (25mm). I can't get at it to create a new thread so what's the best way of connecting the two? Cheers, Peter
Replies
2
Views
158
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
0
Views
109
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock