Hi guys. I’m currently doing some site work and as I don’t leave my tools on site I’m looking for a good tool case/box on wheels if possible. Have any of you lot got anything you’d recommend? Cheers
Is there anyone out there recognise the manufacturer of the shower mixer valve , there is no markings on the leaver or brass work. It has started to leak around the barrel. Thanks
I'm looking for a quality robust sealant between rubber bathroom flooring and sanitary ware as well as gap filling between floor and skirting, it's not a wet room but needs to go off hardish and be easy to clean. Does CT1 fit the bill?
Hi, the 15mm pipe work to my shower use compression fitting, the elbow joint which is in the wall and the pipe comes out and in to the shower is lose and water has been leaking in to the clinker wall. is there a deep socket size 24mm that i can use to retighten the compression nut ? as i can’t...
The drain cock on my water cylinder is very close to the ground and is obscured by piping installed by the previous owner. The spigot is at the bottom but, try as I might, I can find nothing to tighten it. Can anyone offer any advice ? Thanks
Hi, does anybody know what gas is in the freeze master's pipe freezing units, mine could do with a check and a top up. My local aircon branch said they might be able to re-gas the unit if it contained a gas they had. Thanks in advance.
Saw a version by Unilite that made me wince price wise, the end light isn't great but the bar light can open up and brightly light the inside of a boiler or even a loft very easily indeed and placed anywhere with it's magentic base or hanging hook. USB charged, waterproof it's not bad for near...
Hi
I’ve purchased a basin mixer tap for my bathroom.
trying to install the tap and can’t find a tool to fit the nut that holds the tap in place. I’ve tried one of these and it doesn’t fit. To small.
https://www.NoLinkingToThis/p/basin-wrench/13294
I’ve got a diagram of the tap, need to know...
Hi all
Hope everyone is staying safe. Need a little help as over the past few years I have kept my pipe slices in all kinds of containers but have ended up getting broken or just takes too much room in my install bag. Anyone, come across anything decent?
Thanks
Which make is fairly foolproof? I tend to almost always go down the mechanical unblocking route but I want to leave a few bottles for a few tenants (not mine).
Seem to be quite a few making them nowadays... Saxon, Shark but don't want to fork out for Bosch if I can help it, just a fair value assorted pack for timber/plastic. Which are decent?
Hi, I'm about to install a UV water treatment and filter system with 3/4" brass connectors. So I need to buy MDPE pipe connectors, bends etc. I wondered what folk thought about Plasson, FloPlast, Other connector types, especially the plastic to copper connectors, which I believe strip easily...
Grohe kitchen mixer with new - fangled tool free fixing. Had 2 now, both with problems on the clutched plastic backnut - just keeps slipping and turning, not gripping - tap is about as solid as a fresh mackerel.
They are trying to make it easier for diy / handyman but usually it's the water...
Yes I know topic has been covered umpteen times but here is another. Has anyone experience of the Rigid 32573 supposedly goes from
6mm up to 28mm? Only asking as a bit fed up with my Kopex ones, I only do a bit of DIY cutting but have 3 sizes 15,22 and 28. The 15mm is shot
the 28 is plastic and...
Evening all,
As per the title does anyone know where I can source an extension bar for hole saws?
Scenario today: using 54mm hole saw through approx 300 mm wall made up with plasterboard with a ply backing, cavity, a layer of osb, insulation and then a brick outside wall
(Obviously aware you...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.