Hi everyone-im a first time poster and after some info on what type of boiler to fit to my repiped house.
I have an old large house which has currently got a 70kw oil boiler with a single pipe system and pipework is approx 4 inch threaded steel-mega inefficient with school type radiators-the...
At a warmflow bluebird today not firing.I checked there was 240v going into the rdb control which there was
so immediately got a control from the van but no dice same issue.So im getting 240v on my meter but no lockout light .Nothing completely dead.I plugged a mains powered grinder into the...
I've a client with a rusty 20yr+ old Certikin 180 (44kw) oil pool boiler that needs changing. Certikins replacement looks like it is the exact same boiler. It has a riello r40 burner and non condensing 85% efficient boiler... Oftec say it wouldn't be compliant and would have to contact Building...
I've got a problem with an oil boiler overheating the water, I have a solution and if anybody has any relevant advice, I'd be obliged.
I have a Firebird 90S oil boiler, which was installed about 10yrs ago. It has a Cordice 542788 thermostat fitted, which has a range of 60-90c apparently. The...
Thank you for any advise, I was called to attend for a tank inspection following a request to the customer from the environment agency who have found traces of heating oil in a local drain off ditch. (The customer is elderly and has recently lost her husband. ) I found it was single skin...
Have a problem with an oil fired AGA conversion
Has been no problem for 5 years, now goes out 12 to 36 hours after lighting, have checked fire valve, and have installed seperate line from tank to feed AGA
went for 3 weeks one time, then went out due high winds. Has now started same pattern
Help...
Hi,
Am looking after my elderly parents (90 and 94) at the mo... And noticed a burning rubber-ish smell from the back of the boiler earlier this evening.
When I looked at one of the G/Y ones relating to ? thermostat limit settings on the l/h side, I realised it had come loose (and was resting...
Anyone got any suggestion on how, if possible you could clear soot from the condensing heat exchanger of a Grant Vortex. Have many of you encountered blockages like this? Have any of you been able to avoid condemnation of the boiler the due to the stainless heat exchanger being blocked? What can...
Looking for a plumber to pipe up Rayburn to an R type neutraliser (and alter pipework to connect existing oil boiler). Job in SG8 OQE.
The job is fairly straightforward with reasonable access for pipework in roof void. Cylinder might need raising on a platform which I will build (I'm a chippy)...
Hi Folks
I'm wondering anyone here, has any indepth knowledge on the Worcester Heatslave Combi Boiler. This boiler is quite old (2006) but it has been very reliable, and also runs at superb efficiency when tested, regularly serviced etc.
The boiler is in a very old stone cottage (built 1791)...
Bit of advice needed regarding replacing an old Stanley range .Solid fuel.I am trying to source a second hand solid fuel range to heat about 8 rads and also to cook on .My current old Stanley 8 just does the hot water and about four rads badly.No oven and never hot enough to even boil potatoes...
A bit of history first. 2 yrs ago visited a grant boiler with boiler and pipework kettling. I added SentX200 noise reducer.
It is standard open vented system S plan Also found there was no bypass and this was an external boiler with frost stat so boiler would start with no valves open...
Good morning, My old RHINO boiler has developed a small pin ***** leak at this plastic joint, its a threaded cap with some wire coming out top, any one know best cure ? Thanks
Probably been asked before but cannot see where. Inside my boiler there is written nozzle 1.25 x60 W. In an envelope attached to boiler is a new nozzle marked 1.25 x 60 S are they compatible? Boiler is an old Boulter Camray.
I have a 10 year old oil boiler has run well and gets serviced every year all tests are spot on, last week started locking out, would reset and run for short time, engineer fitted new control box and said thats it he was only away 10 minutes and it locked out, now waiting on new photocel, boiler...
Hello,
Re-jigging a serviceable Boulter Camray 2 boiler to run presurised instead of gravity. Manual says it can but we need to fit Manual reset Limit stat and Phail tube to put into boiler for sensor -both available. (Also Expansion vessel obviously!)
This seems straightfrward - any comments...
Hi
We got a Camray 5 Oil Boiler with a timer control panel, is it possible to fit a room thermostat instead or have timer and room thermostat? How would it control both turning the boiler on and turn on the heating pump? Can you get wireless models?
Thanks
Hello everyone,
Looking for some advice...
I have a ‘Boulter Camray 5’ boiler with a ‘Boss Therm’ programmer unit which is located in the garage.
I currently have no thermostat in the house, all rads have TRV's fitted, except one in the utility room.
I would like to fit a thermostat...
Hi, our Bunded 1000ltr plastic domestic oil tank leaking from inner to outer skin, was installed, as part of a new-build, in 2016, to supply a boiler.
When getting it refilled last week, the delivery driver pointed out that the outer skin was bowing out slightly and advised me to check it.
I...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.