Show us your fanciest radiators you've installed! We would love to see them!
I love this Milano vertical radiator in the kitchen space.
What do you think?
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
I am in process of replacing an existing sink with a new stainless steel one. The existing tap is plumbed directly to copper which means that it is earthed. The new tap will use flexible tails and so will not be earth bonded. My initial search for information suggests that there is no legal...
- Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold then would get hot water most of the time. Changing the flow cartridge about 2 years ago (when I moved in) solved this problem enough to suffer it as...
Rad is only a few years old.
Paint is flaking away at the top curved section and it looks like faint spots of rust where the rad is now bare.
Hi bit of a weird issue, I installed a grohe bathroom tap successfully 2 months ago bought from screwfix.
Last week the right hand hot tap makes a squeak noise as I turn it on or off, left tap is 100% perfect and noiseless.
This grohe tap is like one unit, so no screw notch or way I can remove...
I have a green star ten yrs old keeps increasing pressure, feel on off filling valve not working, drain off to recommended, but after few days it's increased whilst cold...is this a regular problem.
Hello to everyone.Im a newbie here. plumbing & heating+GSR engineer.
- Article
A Plumber Who Worked Illegally Gets A Suspended Sentence After Falsely Claiming To Be Gas Safe Registered.
A Plumber in Herefordshire was prosecuted after Hereford Trading Standards Team found that he was falsely claiming to be on the Gas Safe Register when he was not, putting members of the...
Just started gound work on self build bungalow and wondering best way to do below ground soil pipes.
For toilet I was going to go straight down through slab and out through deadwork into a manhole. I will work out falls from manhole and set the height of the waste water system as required.
For...
We run a community village hall and have a large kitchen provided for the use of hirers. This includes a Lincat SLR9 gas cooker which I believe is a 23.8Kw appliance with all six burners and oven on max. This was installed some 10 years ago and has passed all subsequent Gas Safety inspections as...
I have had a look at previous posts and think I know the answer to this but just before I make it worse could I just check what you think about this one.
Granddaughter just moved house and this valve decided to leak when it was closed.
When open its fine.
Normally I have repacked the gland on...
The left rear floor corner is highest (the shower pan touches/sits on the floor), sloping down diagonally to the front right corner (lowest). The front right corner shim is 5/8", the left front corner is 3/8" shimmed, with shorter shims under left middle and right rear corner.
The pan perimeters...
Our kitchen mixer tap has started dripping. Like so much of the plumbing in our almost new build bungalow, it is lacking! The plumber didn't install any isolating cocks in the H&C feed to the tap so how can I identify which of the valves is passing? Shut the whole H&C water system down?
Hi all. Hope you have all been keeping well.
A while back I decided I only wanted to fit one brand of boiler and decided on Viessmann due to space for servicing and changing parts if ever needing to. I am finding my decision rather hard due to the different clearances on flue runs and cupboards...
Can anyone recommend a decent multi meter, preferably under a 100 pounds. It's for checking boiler components so I don't need a top spec one ....just easy to use and reliable.
The fluke 115 looks good but its above my budget. My current socket and see one was great but it's developed a fault.
We are from Alberta, and I own an electrical company.
I have been asked by a BC Mechanical P. Eng. to install an emergency STOP button at the man-door to the boiler room. It's intent is to 'halt' the operation of the boilers in the room should there be an emergency. He is demanding that I do...
Can anyone remember the Mira mixer shower that would work down to a really low pressure on a vented hot water system without a shower pump?
Every two weeks or so I have to go and top up the system because the hot taps are running cold. Boiler display is flashing 0.6 bar and I fill up to 1.3. I've had an engineer look inside the boiler and he can't see anything wrong. I've checked the pipes all over the house and cannot see any...
Hi everyone,
Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Creating content since 2001. Untold Media.
Newest Plumbing Threads
-
-
-
-
-
Mixer mixer shower, compatible with tanked supply
- Started by Matt0029
- Replies: 2
-
-
No Hot water, Fixed and Broken Again Ideal Logic 24
- Started by Filthbags
- Replies: 2
-
-
What's happening to this radiator, paint flaking off?
- Started by mikmikmikmik2024
- Replies: 3
-
Is it necessary to earth bond a Kitchen Sink?
- Started by Cello
- Replies: 5
-
Show us your fanciest radiators you have installed!!
- Started by Lou
- Replies: 2
-
Y Plan, no hot water but heating is working when called
- Started by Chopper9495
- Replies: 8
-
-
Towel Rail Valve Advice please (35 Characters needed.)
- Started by NorthernLad
- Replies: 7
-
Unvented discharge at high level current regs
- Started by Matt0029
- Replies: 11