Activity Stream
-
Older Activity
-
1 Minute AgoDitto3 replies | 98 view(s) -
10 Minutes Agoeliteplumbing91 replied to a thread Link Exchange - Plumbing Site in Links, Forum Updates, News and Site SuggestionsHi, we provide plumbing services. Elite Plumbing & Gas is a QBSA Licensed, and locally owned and run busines by Matthew Cary. Matt started his apprenticeship back in 2004 learning both the gas and plumbing trades, and in 2010 decided it was time...2 replies | 2311 view(s)
-
4 Hours Agoi clean my own system out every morning! ;) i have the combi mag, its great.2 replies | 76 view(s)
-
5 Hours Agoa little more to it than flame picture and gas rate, though sadly many dont go past flame picture.12 replies | 148 view(s)
-
5 Hours Agounless theres a need to run the cylinder all the time along with the heating then you should not need to add them up together. Make sure the controls allow seperate running.3 replies | 98 view(s)
-
5 Hours AgoHello and welcome28 replies | 208 view(s)
-
6 Hours AgoThe chimney opening shall have only two openings: The front of the builders opening and the opening in the flue liner. All other openings including the annular space between the chimney and liner must be sealed, this includes the sides of the...30 replies | 312 view(s)
-
6 Hours AgoAnything with a 6" centre1 replies | 13 view(s)
-
6 Hours AgoTake off towel rail, fill with water upside down plug inlets refit to valves one at a time. I know this might sound a stupid idea and would need done again if system was drained down but its the only thing i can think of without replacing towel rail5 replies | 49 view(s)
-
6 Hours AgoIt's an old one then. You'll get it out with an easy out (google it) or saw a better slot in it (you will damage the shoulder but it shouldn't be noticeable)5 replies | 49 view(s)
-
6 Hours AgoI have two of these in the garage going for scrap, you are welcome to the bleed screws if it will help you.5 replies | 49 view(s)
-
6 Hours AgoMaterials i have no idea but as for labour that can very on the set up. when you do it you will need new zones valves, tank stat, pump and programmer. new wiring centre and thermostat if you feel like it too. it really isn't somthing that you...30 replies | 312 view(s)
-
6 Hours Agoanybody know of a good replacement for a exposed one of these without re doing the pipework????1 replies | 13 view(s)
-
7 Hours Agonoooo tamz like a blody sinked self tapper kind of theing UNDER the bar! and to make it wor its a slotted one, whoever invented slotted screws ...............5 replies | 49 view(s)
-
7 Hours Agocheers guys, on another note what would the cost be of changing to a fully pumped system, sure I have seen them sold as a kit for everything needed30 replies | 312 view(s)
-
7 Hours AgoBleed pin head on the back of the rail? What a bummer :lol:5 replies | 49 view(s)
-
7 Hours Agooops thats the link for the lid, but they do them !26 replies | 164 view(s)
-
7 Hours AgoAKW ergonomic toilet seat with lid Blue do them with flush handle , nightmare if they go wrong tho!!!26 replies | 164 view(s)
-
7 Hours AgoI use a 1000x24 drill bit for that......so I can drink my coffee from the kitchen chair ! Lol799 replies | 139944 view(s)
-
7 Hours Agodont know if its been mentioned before but, when drilling with a long drill bit from inside of property to outside , mark the bit with insulating tape so you know when to turn hammer action off sds when your abou 1/2" from the outside , this...799 replies | 139944 view(s)
-
7 Hours Agohi lads, went to a job today to fix a towel rail , wasnt getting warm , anyway sorted that and noticed it was only getting hot to middle (top full of air) now i cant open the bleed key as its totally rounded/flatend , and i cant replace it as ive...5 replies | 49 view(s)
-
7 Hours AgoWell done Tom :50:24 replies | 201 view(s)
how many killowatts to add....
1 Minute Ago in Central Heating Forum